Hyundai Cars & Trucks - Page 6 - Recent Questions, Troubleshooting & Support


crankshaft position sensor...when its bad the engine shuts down..might restart after cooling off, but sensor needs to be replaced.

2001 Hyundai... | Answered on Sep 30, 2019


if its the V6 2.7l its below the coil packs and behind cooling fan(must remove to replace it) on the side of the block, Drivers side... gonna need a flashlight and long extension...kinda hidden but its there follow the wire/connector back to the block....if its 4 cylinder its passenger side behind timing belt...must remove passenger wheel and timing belt cover..

2004 Hyundai... | Answered on Sep 30, 2019


Broken window regulator inside door. You'll have to remove the door trim panel, remove the glass and then replace the regulator. The part is around $100.

Hyundai Cars &... | Answered on Sep 29, 2019


There Are 2 different glow relays . I hope that answered your question.

Hyundai Cars &... | Answered on Sep 27, 2019


I just got the same message today...and rarely use the cd player. Was wroking, went to change cd's, then it would not load and gave error 43...anyone?????

Hyundai Elantra... | Answered on Sep 26, 2019


Michel: timing chains don't need changed like a timing belt does so Yes that is right.
A timing belt stretches over time and heat but timing chains usually out last the life of the vehicle. I have 210,000 miles on my personal vehicle and the timing chain is still original. Hope this puts your mind at ease.

2011 Hyundai... | Answered on Sep 25, 2019


The service and repair manual will provide you all the knowledge you need with diagram to fix the problem easily and you will get the factory original manual from the given link https://toolsnyou.com

Hyundai Cars &... | Answered on Sep 25, 2019


follow this link for the headbolt torques etc, click on torque tables and look up your vehicle
http://www.speedwayautoparts.com/index35.htm

2008 Hyundai... | Answered on Sep 25, 2019


Relay should be in the power distribution center under the hood.

Hyundai Cars &... | Answered on Sep 24, 2019


with your eyes closed and one hand behind your back if you follow my smple instructions ,firstly remove no1 spark plug and bring it to TDC using a long thin screwdriver then drill a 10mm hole in the bellhousing to align with starter ring gear ,then tap it and make a long bolt with a point on the end by grinding it down but a put a nut on it first so you can back it off so the thread is ok ,then screw this into the hole to lock the flywheel ,now its safe to remove the front pulley bolt as this car is on a taper with no keyway on the end of the crank,then take the pulley off and this allows removal of the timing cover .Now a touch of white paint on the cam pulleys to the back plate ,slacken the belt adjuster and remove the belt ,then take of the adjuster and any idler pulley ,use a thin screwdriver to remove the thin seal ,drop into a drop of petrol and clean out best you can ,then a can of brake and clutch cleaner and spray teh bearing balls a bit ,shake dry light oiling with engine oil the repack with lm waterproof grease ,not the black grease for a drive shaft .Refit the seal then refit the idlers and put the belt on making sure the cams dont mose a pair of mulgrips help here to hold the belt to the cam gear .Once all on and tight refit teh covers and the front pulley then tighten the pulley bolt with a decent snap on knuckle bar of 80cms and a tube over the end as you need somewhere around 120lbs to stop the crank gear pulley wheel from turning on the taper as you what happens if this moves ,yes new valves ,simple isnt it ,also you will need a bottle jack with some wooden blocks to support the sump whilst you remove engine mounting wood under the sump or you will break it as its ally .Should take no more than two hours including tea break and a ciggy

2008 Hyundai... | Answered on Sep 24, 2019


Hi there's this website something like reliable-store and it is very amazing for manual for repairing servicing anything
someone on fixya recommended it to me and I thank him even today
They have full manuals and it's verrrrry cheap and mine
I got free in offers
3rd time I bought it, I also had an issue with the file so the girl replaced it in 30 mins
there is one website more but i don't remember its name it was 2 years back bitman something link this
Try these out brother

Hyundai Cars &... | Answered on Sep 23, 2019


Lincoln was it shaking before the new tires? I ask because I've had new tires put on , headed home and mine shook. I turned around and made them balance them again. Like Mike asked, do you feel it in the steering wheel or does it feel like the whole vehicle is shaking? Did you put your tires on or just two? You could have a tire out a round or one with a bubble on it even if they are new you could have one defective. I had new ones on mine once and I felt something weird like a shake in mine. I stopped and checked but saw nothing. Drove about two miles farther and my left front NEW tire blew out right in the center of the tread. Luckily I wasn't going very fast and when I stopped and looked I must of been sitting on the bad spot. New doesn't mean much anymore, everything is built/made with robots & computers. To me that means no quality control. Good Luck, I hope one of these ideas help you find the problem.

Hyundai Santa Fe... | Answered on Sep 21, 2019


I searched using Google.com and the following suggested locations to check are shown below:

https://www.yourmechanic.com/question/where-is-the-fuel-inertia-switch-on-a-2010-hyundai-sonata-by-heather-b

"On some Hyundai models, the switch is to the right of the brake master cylinder. Look for a switch with a red button. Other locations that Hyundai has used for this switch are in the passenger glovebox area and in the trunk. Those locations might be concealed. For more detailed advice on how to locate the fuel cut off switch please see YourMechanic's fuel cut off switch tutorial. If your vehicle has not been in a crash, and it doesn't start, it is unlikely that this switch is at fault. If your vehicle is not starting, the appropriate diagnostic is a no start diagnostic. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you. "

Hyundai Cars &... | Answered on Sep 20, 2019

Not finding what you are looking for?
Hyundai Logo

43,271 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2004 Hyundai Santa Fe
2004 Hyundai Santa Fe

1,447 Questions

2001 Hyundai Elantra
2001 Hyundai Elantra

1,154 Questions

2000 Hyundai Accent
2000 Hyundai Accent

1,113 Questions

2006 Hyundai Sonata
2006 Hyundai Sonata

1,216 Questions

2001 Hyundai Accent
2001 Hyundai Accent

1,057 Questions

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...