20 Most Recent 2009 Buick Enclave - Page 7 Questions & Answers

make sure the dome override switch is depressed. The switch is located just above the rotating knob which dims the interior ligthts. The dome overide switch is located just to left of the steering column.

really. it's ridiculous how tight things are packed in there these days. but it's still under there, probably almost hidden under the air filter box. look for exposed battery posts right behind one of the headlight assemblys

If you are talking about the homelink built in to the car then you will have to look in your manual. There is a sub section devoted to this. Each car line is a little different so I can't get too specific. You do have to determine if your opener has a rolling code though as this adds a step to the programming process. The clearing factory/old codes out of the car is not optional but has to be done too. Thanks BB

Have you looked in your phone menu for auto answer You may find it under tools. If you can't find it, get a hold of ONSTAR and ask them to set it back to normal.
http://www.onstar.com
Or best way is to call them from your car phone.

Make sure all your fuses are good. If this is not the problem you may need to turn your car in for repair, because this problem could be a lot of things.

Sent vehicle to dealership.

Here's the info from GM:

Condition/Concern: Some customers may comment of a helicopter type noise when a rear window is lowered. This is known as buffeting and it is a low frequency, high volume wind noise that may occur in a moving vehicle with a rear window open.

Recommendation/Instructions:This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches. Installation of accessory weather deflectors along the front door glass may also be effective in alleviating the buffeting noise. Seems to me there's nothing to pay for with this info. This is common in alot of vehicles I've dealt with in my career. I'd say if the dealer wanted you to pay for them to tell you that, maybe you should find help somewhere else.
The Enclave is a really nice vehicle. Don't let poor customer service from a dealer discourage you from enjoying your car.

It appears that you may not have the latest GPS software. Since your car is brand new, I recommend going to the dealer and having them update your system as it will be free

Need to use a scanner to see if there are any codes pertaining to the transmission. https://www.acadiaforum.net/threads/2010-wont-shift-out-of-first-at-cold-start.13432/

Checked code's where ? Full system scan or just OBD2 . What type scan tool ? Or is it just code reader ?

Hello. It seems either your a/c control panel is defective/malfunctioning and/or a freon condition; either too much or too little. Good luck and keep me informed; if you want to.

You can do it yourself. Apparently it is called a Power Window Reset and the instructions are in the manual. https://www.enclaveforum.net/threads/auto-up-windows.8058/ videos here as well https://www.google.com/search?q=buick+enclave+power+window+motor+programming ..

Yes,you should be able to move the blend door with your fingers

Yes there is a air temperature control door and that is moved by a small electric that can hold its position according to the temperature setting you desired.

Actually, a new rear wiper module/motor is probably needed. The logic controller is on the motor so the entire motor has to be replaced. I believe the switch is on the center console and I think you will need to remove the outer trim to get at the switch. It may be a switch that just snaps in, so I would get a look at a new one before digging into the job.

What year ? The relay's are located in the under hood fuse box . With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER relay, the WIPER HI relay and the WSH relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics. Which wipers are you talking about ? Front or rear . Rear wiper fuse is in the I/P instrument panel fuse box . Fuse Block - I/P Under the lower right side of the instrument panel

bad connection at the circuit board connector