20 Most Recent 2009 Chevrolet Silverado 1500 Questions & Answers


Rather gona be special fuse box under hood or usually along fire wall under hood

2009 Chevrolet... | Answered on Jan 22, 2018


Usually a sign of a faulty blend door under the dash.
The blend doors direct air thru the ac and heater core along with the upper and lower vents.

2009 Chevrolet... | Answered on Nov 25, 2017


Evap. vent solenoid is under the vehicle near the fuel tank , connected to the charcoal canister .

2009 Chevrolet... | Answered on Oct 29, 2016


This is very complex , first thing is have the vehicle checked for DTC'S - diagnostic trouble codes stored in the BCM , PCM !
The body control module (BCM) monitors the signal circuit of the cruise control switches. The BCM relays the cruise control switch status to the engine control module (ECM) via the GMLAN serial data circuit. The ECM uses the status of the cruise control switch to determine when to capture and maintain the vehicle speed. The ECM monitors the vehicle speed signal circuit in order to determine the desired vehicle speed. The ECM uses the throttle actuator control (TAC) motor in order to maintain the vehicle speed. For further information on the TAC System, refer to Throttle Actuator Control (TAC) System Descriptionfor the 4.3L engine or Throttle Actuator Control (TAC) System Description for the 4.8L, 5.3L, 6.0L, 6.2L or 7.0L engines.
Your best bet would be to take to the dealer !
Yo

2009 Chevrolet... | Answered on Oct 24, 2016


You need the dealer to scan the Body control module for faults.

2009 Chevrolet... | Answered on Jul 20, 2016


Simple answer is replace the radio, GM does not service any internal parts on radios.

2009 Chevrolet... | Answered on May 25, 2016


Did you check low beam fuses for voltage, with headlamps on lo beam? Use a testlite to check for voltage. In the diagram you see the lo/hid relay, correct? I'm not saying the relay is faulty, you need to check voltage and ground. The bcm and dimmer switch are involved, I don't know if check for headlamp/lighting trouble codes will help? Don't replace anything unless your testing points in the direction.
no-low-beam-headlights-beam-okay-fuses-cskqpewkyt2g1jj30lipok3m-3-0.jpg

2009 Chevrolet... | Answered on Mar 04, 2016


You have a short somewhere. You might have some wires melted. I would disconnect the battery to prevent more damage. Visually check the fuse box and the fuses. If you find anything burnt or smell something burnt. Have a mechanic trace the short to repair.

2009 Chevrolet... | Answered on Feb 21, 2016


cruise control module has failed. or if your brake lights are staying on, then brake light switch has failed and not allowing cruise to engage. Have someone stand behind truck and see if brakes are working properly, if not- replace brake light switch. if fine, then swap out cruise control module under hood.... prob find one at a junk yard.

2009 Chevrolet... | Answered on Feb 02, 2016


Are the fans running on low or high ?
Circuit/System Description
The engine control module (ECM) commands the fans ON in either high speed or low speed, depending on cooling requirements. In low speed, both fans are turned ON at a reduced speed. High speed has both fans turned ON at full speed.
In low speed operation, the ECM applies ground to the coil side of the fan low relay. This energizes the coil and applies voltage directly to the left cooling fan through the switch side of the fan low relay, which is fed by the fan 1 fuse. The right fan is connected in series to the left fan through the de-energized fan control relay so that both operate at low speed.
In high speed operation, the ECM applies a ground to the coil side of the fan low relay, the fan control relay , and the fan high relay. On the fan high relay, the energized coil closes the switch side of the relay and applies voltage directly to the right cooling fan through the switch side of the relay, which is fed by the fan 2 fuse. At the same time, the ECM energizes fan control relay pulling the switch side over, providing a direct path to ground for the left cooling fan, which has voltage applied through the energized fan low relay. In high speed mode, the fans are operated as a parallel circuit with full voltage applied to each.
You should have it hooked up to a scan tool that can read engine sensor data parameters . Check for DTC'S - diagnostic trouble codes etc...
Circuit/System Verification
  1. If DTCs P0480 or P0481 are set, perform those diagnostics first.
  2. Ignition ON, verify with a scan tool that the control module is not commanding fan activation.
  3. Ignition ON, observe that the fans are not activated.
Your best bet is to take it to a ASE certified repair shop !

2009 Chevrolet... | Answered on Jan 11, 2016


Here's a link to your code. Vauxhall Workshop Manuals

2009 Chevrolet... | Answered on Aug 26, 2015


DTC P025A: Fuel Pump Flow Control Module Enable Circuit
The engine control module (ECM) supplies voltage to the fuel pump flow control module (FPCM) when the ECM detects that the ignition is on. The voltage from the ECM to the FPCM remains active for 2 seconds, unless the engine is in crank or run. While this voltage is being received, the FPCM closes the ground switch of the fuel pump and also supplies a varying voltage to the fuel tank pump module in order to maintain the desired fuel rail pressure.
Circuit/System Testing
  1. Ignition OFF, disconnect the harness connector at the FPCM.
  2. Ignition OFF, install a test lamp between the control circuit terminal 13 and ground.
  3. Ignition ON, verify that a test lamp illuminates for 2 seconds.
  4. ?‡'
    If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.

  5. If all circuits test normal, replace the FPCM.
Relay for what ? Which engine do you have LY6 or non LY6

2009 Chevrolet... | Answered on Aug 25, 2015


Cylinder location Drivers - Passengers
1 2
3 4
5 6
7 8
#1 is closest to the front of the truck.
Firing Order 1-8-7-2-6-5-4-3

2009 Chevrolet... | Answered on Jun 26, 2015


Evap system has many parts , cannister,vent and purge valves ,fuel tank and cap, first is the fuel cap on and is the seal in good shape. You will need to inspect all vauum hoses that leave the cannister if all ok then get the valve and solenoid tested for stuck open

2009 Chevrolet... | Answered on Mar 23, 2015


Encoder motor ,..........................

2009 Chevrolet... | Answered on Mar 10, 2015

Not finding what you are looking for?
2009 Chevrolet Silverado 1500 Logo

279 questions posted

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Silverado 1500 Chevrolet

  • Silverado 1500 Chevrolet

Most Popular Question

evap vent sensor located 2009 chevy

  • Cars & Trucks
Loading...