20 Most Recent 2009 Honda CR-V Questions & Answers


96 to 2002 Civic, Accord, CRV automatics: The shift solenoid pairs, usually 2 pairs - upper and lower, are very sensitive and get sticky with age. I don't know how many miles you have on your car, but its usually rewarding to take them off and clean them and test them with a good 12v battery. The plunger should move an 1/8th inch with a good snap. If one is stuck whack it face down on a clean piece of paper, blow it out with a compressor and try again. Solenoids can cause starting out in the wrong gear, missing gears, creep in neutral, drag, bad downshifting, shudder, etc... Lower front solenoids are under a metal cap with 3 10mm bolts. Passengers side. Down there at the rear passenger side of the trans is the speed sensor, make sure the connector is clean and wires not damaged. Most of the time it is stuck or weak solenoids that cause these shifting issues. Each solenoid works on a separate gear actuation pathway.

2009 Honda CR-V | Answered on Nov 04, 2017


Inside the fuel pump moduel in the gas tank is a little known part called a

FUEL PUMP CHECK VALVE ! The pupose of this check valve is to keep the fuel lines an fuel rail full of gas . Having it checked would involve hook up a fuel pressure gauge . An no it's not you starter .

http://www.thesaabsite.com/faqs/9-5%20(9600)/FAQ--fuel-system-category--fuel-pump-check-valve-issues.html?id=682

2009 Honda CR-V | Answered on Mar 21, 2017


try with number 29 or 30, base on the fy=uses diagram you have accesories run by these fuses, that could be where the problem is.

2009 Honda CR-V | Answered on Nov 23, 2016


If the brake lights are not working then it will not come out of park.

2009 Honda CR-V | Answered on Jul 01, 2016


it could be a blocked fuel filter, or a flat spot in fuel line ????

2009 Honda CR-V | Answered on Apr 21, 2016


Go to setting , there you will see add a device and than remove the device . Simply remove all the Bluetooth devices which are or were paired with car's than switch the SUV off and than ON . this is the time to pair your phone again , hopefully it will work .
If it doesn't let me know , I will give you another technique .

2009 Honda CR-V | Answered on Apr 07, 2016


Check the Manuel for the audio code card/number, if you don't ha that call the dealer and give them the VI number and they will give you the audio code. Reply

2009 Honda CR-V | Answered on Mar 12, 2016


VSA vehicle stability assistance, you may have accidently pressed the button on the left side under the heater vent, if the switch is on then check the VSS sensors at the wheels to make sure there are connected. Reply.

2009 Honda CR-V | Answered on Mar 12, 2016


The best way to fined out what is leaking is to have a smoke test done at the gas tank, now the gas cap could be fine but the filler neck could be rusted and leaking and you may get the same message as there is NO pressure being created in the gas tank.

2009 Honda CR-V | Answered on Mar 12, 2016


unless you have a problem in the pulley bearing of the ac compressor , just disconnect the power wire to the compressor and use the standard belt
the pulley is just an idler pulley until the clutch is activated so if there is no power to activate it it is just an idler

2009 Honda CR-V | Answered on Dec 16, 2015


call a mechanic,head gasket is shot,probably warped heads

2009 Honda CR-V | Answered on May 31, 2015



Hi Nancy,

Typically pads need to be changed more than once before rotors needs to be *replaced*. Most shops machine rotors when changing pads to give them a smooth, even surface. Machining removes groves that cut into them as a result of normal wear (or if pads are not replaced promptly). Machining can straighten warped rotors due to excessive heat / quick cooling. These are definitely NOT considered "worn out".

Worn out rotors must be *replaced* if they are too badly damaged, rusted, etc. or if they have been machine so many times that they are too thin to safely brake the car. There are specific guidelines that spell out exactly how thin rotors can be before they must be replaced. Mechanics measure the thickness of the rotor with a micrometer which reveal thicknesses to the 1/1000 of an inch.

I hope this was helpful & good luck!

2009 Honda CR-V | Answered on Nov 20, 2014


Trans problem

STOP using it & get it checked out

2009 Honda CR-V | Answered on Oct 09, 2014


The parts store you purchase belt from should be able to give you the routing.

2009 Honda CR-V | Answered on Aug 08, 2014


it means your auto gearbox has a problem, which needs to be rectified, go to a qualified mechanic before its too late, as overtime, faulty gearboxes tend to break down more resulting in higher repair costs

2009 Honda CR-V | Answered on Jul 16, 2014

Not finding what you are looking for?
2009 Honda CR-V Logo

199 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2003 Honda CR-V
2003 Honda CR-V

530 Questions

2004 Honda CR-V
2004 Honda CR-V

431 Questions

2002 Honda CR-V
2002 Honda CR-V

388 Questions

2005 Honda CR-V
2005 Honda CR-V

359 Questions

1998 Honda CR-V
1998 Honda CR-V

327 Questions

Top Honda Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

CR-V Honda

  • CR-V Honda

Most Popular Question

crv will not start sounds like s not

  • Cars & Trucks
Loading...