2013 Dodge Charger - Answered Questions & Fixed issues
Abs light and traction light came on at the same time
You need to have the ABS system scanned for fault codes and then the problem can be diagnosed. The one problem will have caused both warnings to display and it might just be a failed wheel speed sensor.
In any event check your battery condition first. If you have a weak battery this can trigger the ABS and TC warnings but in a 2013 car your battery should still be OK.
12/23/2015 3:10:28 AM •
2013 Dodge...
•
Answered
on Dec 23, 2015
•
337 views
2016 Dodge Charger RT. Vibration gear downshifting 2 to 1.
Question edited for clarity.
No it isn't normal. There is probably a change solenoid or sensor issue. Take it to a transmission place and they will put it on a fancy scan tool computer. Tell them you want to see the results. Don't let them tell you that you need a new transmission!
What is the Firing order on my 2014 Dodge Charger Se 3.6 L
If this is the engine without a distributor the firing order is
1, 2, 3, 4, 5, 6,
The cylinder heads are numbered as odds and evens. Standing with the belts and pulley nearest to you, (the transmission furthest away), the left side is the odd numbers and the right side is the even numbers.
Number 1 is the left one nearest to you, number 2 is the right one closest to you, 3 is middle left and 4 is middle right, 5 is the far left and 6 is the far right cylinder.
Bolt torque specs for 2012 3.6 dodge charger
Here are the specs you require:
• Camshaft Sprocket Bolts 75 +1?4 Turn ft-lbs
• Camshaft Thrust Plate - Bolts 28 ft lbs - 250 in lbs
• Connecting Rod Cap -20+ 1/4 turn ft lbs
Here are the four steps you should take:
1. Cylinder Head Bolts* 45 ft-lbs
2. Cylinder Head Bolts* 65 ft-lbs
3. Cylinder Head Bolts* 65 ft-lbs
4. Cylinder Head Bolts* +1?4 Turn +1?4 Turn
4/28/2020 11:12:17 PM •
Dodge Charger...
•
Answered
on Apr 28, 2020
•
13,128 views
Not getting fuel to motor on my 2007charger
Well, this could be a number of things.
First, check the fuse for the fuel sending unit to be sure there's power going to it. Next, turn the key to 'power on' but don't start it and try to hear the sending unit 'humm' while it's priming the lines.
If you can hear it or you know there's power, pull the key and get underneath and disconnect the fuel line just after the filter and put the key back in and turn it back to the power on, but no start. If everything's good then fuel will start coming out of the lines and you know that there's most likely a blockage further downstream and it's not a faulty sending unit. Good luck!
Location of o2 sensor 2006 dodge charger sxt 3.5
There is no names, but just fuse numbers. I have an 06 6.1 and am looking for the fuse or relay for bank 2, sensor one. I've replaced both O2's because im receiving a p0052 code. The bank 2, sensor 2 that was showing a code is gone, but the sensor 1 is stillthere. All grounds are good, pcm is new, but still showing a code while the car is in limp mode. All fuses are good, but i cant check the relays.
11/3/2018 4:21:22 PM •
Dodge Charger...
•
Answered
on Nov 03, 2018
•
2,292 views
Where is the Ambient Air Temperature Sensor located on a 2009 Charger 3.5 V6?
That sensor is usually out front in front bumper fascia and relatively small. It can be clipped in anywhere and some are harder to see than others. Usually located on the driver side of the vehicle. It may be in a small hole and has a probe sticking right in the middle of it. Hope this helps you in locating your sensor. Jesus loves you, John 3:16-17 (KJV)
Not finding what you are looking for?