20 Most Recent
2013 Chevrolet Cruze - Page 5 Questions & Answers
2011 chevy cruze spongy brakes
Spongy brakes are usually a sign of air in the system. Get a good mechanic to bleed the entire system, all four wheels. He'll be able to check the brake pads and discs while he's doing it.
Need torque sequence for main saddle bolts . 22 in total for a 2012 chevy Cruze ecotek 1.4l turbo
Special Tools
- EN-235-6 Installer
- EN-470-B Angular Torque Wrench
- EN-658-1 Installer
For equivalent regional tools, refer to Special Tools.
- Install a NEW crankshaft position sensor reluctor ring?(1) and the 3?bolts?(2).
- Tighten the 3?bolts?(2) to 10?Y?(89?lb?in).
- Lubricate crankshaft, crankshaft bearings and crankshaft bearing cap tie plate with engine oil.
- Install the 4?upper crankshaft bearings?(2) and the crankshaft thrust bearing?(3).
- Install the crankshaft?(1).
Note: The thickness of the sealing bead should be 2?mm?(0.0787?in).
- Apply sealing compound?(1) to the outer rim of the groove on the crankshaft bearing cap tie plate. Refer to Adhesives, Fluids, Lubricants, and Sealers.
Note: The complete installation procedure should not take longer than 10?minutes.
- Install the 4?lower crankshaft bearings?(3) and the lower crankshaft thrust bearing?(4).
- Install the crankshaft bearing cap tie plate?(2).
Note: Do not reuse the old bolts.
- Install the 10?NEW inner crankshaft bearing cap tie plate bolts?(1).
Caution: Refer to Fastener Caution. Caution: Refer to Torque-to-Yield Fastener Caution.
- Tighten the 10?inner crankshaft bearing cap tie plate bolts in the sequence shown and to the following specifications:
- Tighten the inner crankshaft bearing cap tie plate bolts to 25?Y?(18?lb?ft).
- Tighten the inner crankshaft bearing cap tie plate bolts an additional 60?degrees, using the EN-470-B wrench.
- Tighten the inner crankshaft bearing cap tie plate bolts an additional 15?degrees, using the EN-470-B wrench.
Note: Do not reuse the old bolts.
- Install the 12?NEW outer crankshaft bearing cap tie plate bolts?(1) and tighten to the following specification:
- Tighten the outer crankshaft bearing cap tie plate bolts to 10?Y?(89?lb?in).
- Tighten the outer crankshaft bearing cap tie plate bolts an additional 60?degrees, using the EN-470-B wrench.
- Tighten the outer crankshaft bearing cap tie plate bolts an additional 15?degrees, using the EN-470-B wrench.
- Install the crankshaft position sensor?(1) and a NEW crankshaft position sensor seal ring?(2).
- Install the crankshaft position sensor bolt?(3) and tighten to 8?Y?(71?lb?in).
Note: Lubricate the crankshaft rear oil seal.
- Install the crankshaft rear oil seal?(1) with EN-235-6 installer?(2).
- Use EN-658-1 installer?(1) to strike the crankshaft rear oil seal.
My database showed this info. Only the inner 10 showed a sequence. The outer 12 didn't.
How to reset anti theft system on a 2015 chevy cruze
Hello Elizabeth...
I picked this up from another blog on line so I can't guarantee success with the below:
Remove key from car,remove positive battery cable for about ten minutes,then place key in car and to the on position,then replace battery cable.
PS: Your owners manual may also provide some assistance.
Not finding what you are looking for?