20 Most Recent 2012 Acura RDX - Page 4 Questions & Answers

IT means the computer is seeing an intermittent signal from the crankshaft position sensor. Bad sensor or a wiring issue.

Hi, please look around the engine of your car. You can use a website like advanced auto parts to view what the object looks like and use this image during your search. If you can't find it, you can drive to your local advanced autoparts and let them locate it for you. Thank you.

I am not seeing any inertia switch in the wiring diagrams. You need both the PCM-FI Relay1 and Relay2 functional for the fuel pump to run. Relay2 runs the fuel pump and draws it's control power from Relay1. I suspect that your fuel pump is starting to get weak and the hard bump is enough to knock the pump stater out of alignment enough to slow or stop the pump. Try using a DVM with DC current loop to measure current across the load side of relay2 at a time which the pump is not working (this can be done by removing the relay and placing a wire loop across the load terminals 30 and 87. then place the wire through the loop on your meter- if you are seeing current when you turn the key on and the pump is not spinning, the pump is very likely bad. If you dont see any current, then there could be a fault in the wiring harness going to the fuel tank, or a fault in the wiring inside the fuel tank.

I need to know the location of a 2010 Acura tl crankshaft sensor

Sounds like you need to find a competent transmission shop.

HELLO ,This is answered here 1000 + times. lets do 1001. so starter motor is dead silent ,dead, and can not crank here it is one more time. battery good,charged and all 4ends of battery cables not rust, or loose (lugs) not tight,

1. all fuses good skip none , cab and engine bay all.
2. is headlamps dead key on or off?
3. is keyon blower for heater dead on blow high?
4. is cluster dead key on? is IMMO lamp NOT HAPPY,.BINGO.
5. are other things electric vast dead.(all good and bad matter in the electric world. (power tree reasons)
6. Scan the PCM see why ? oops PRNDL failures. , battery failures , fuse feed failures DTC? endless list of possibles and not scanning is never ever wise.
7. Does the PRNDL shifted to Neutral wakes up the starter
8. does jumper cable jump starts work? as see AAA club tow? guys./
9. does hot wiring the starter work (ask) all techs know how.
10. if #9 files the starter is bad ,battery not.
11. if land here, relay may be bad.

kill switch? perhaps the key. If you are talking about fuel reset switch there is not one.

https://youtu.be/sGzxCCaxDjI Here is the link.

Hi, Please first check the manual of your Acura for the description of those wires . If not found, please call Acura at 1 (800) 382-2238 in order to ask them to email you the wiring diagram corresponding to those wires. Thank you.

you dont have an inertia switch

Check that it's getting fuel Check spark Fuses

drivers side kick panel remove cover fuse box and relays are behind panel. The starter relay is bottom row of relays right side Good Luck Mike

https://video.search.yahoo.com/search/video?fr=mcafee&ei=UTF-8&p=2004+acura+flashing+D5&type=E211US1494G0#id=1&vid=3a92334774e2ea274b49bfc3d3d0ad96&action=click Watch this video

Check the engine compression first. It may have gotten hot enough to take the temper out o9f the rings. Other possibility, did coolant spray over the engine? You may have a sensor that went bad when it got wet or a wire connection. Before taking off the fuel rail, check the fuel pressure. Also check the ignition for spark.

the IMMO is bad scan it, next if all fuse are good the scan tool tell you why IMMO is not happy with DTC errors is suggestion was dead on. He is not CAR ASE tech, he is a locksmith.

This is the three ways to get a radio code. Only one is available to you unless you can get a local Acura dealer to cooperate. https://www.fixya.com/support/r29874205-need_vehicle_radio_code ..

what country?> if canada or have DRL lamps say so first, DRL love to fail daylight running lamps, only you know this.answer. both head lamps dead a night and day high beams and low beams. all fuses good, for sure heads. head lamp relay bad scan tool shows wire or did not scan it next. the balance means what, all other things on car works and drives ok, and no check engine lamp glowing? or GEN/ battery lamp glowing in IP cluster ,running./ head lamps work key on or key off by law here <USA. sure does and if fails key off, that is hard failure to fix first.

The module should be in the above console panel by the mirror in the overhead. This module can be bought on ebay as a suggestion only Good Luck

pressure test system -----you can be burning it just not having the billowing smoke --

something draining the battery will not kill it that fast so let us start this way, first it sounds like no charge problem now a blown fuse in any major part or item in the fuse box blown will stop it from charging also it could be the alternator which most auto parts will check free last thing can you tell me once you crank it and just let it sit there and run does it die? we can go from here when you check back good luck