2007 Chevrolet HHR Fall - Answered Questions & Fixed issues

Before you do that turn on your hazard flashers then off again a couple of times some times dirt gets around this switch and causes lights not to work.

too long to list lol If you need further help, I’m available over the phone at https://www.6ya.com/expert/david_4c166ba81493f541

Some bulbs are really tough to remove on this car. Specially the front side lights. You have to first remove the panel in front of the tires. Hope this helps.

check for compressor clutch operation, if the clutch is engageing you could have a bad compressor or a blockage in expansion valve

My daughters 1996 Nissan Maxima keeps stalling on her when she leaves a stop. Any solutions to her problem. Oh, her engine light is on too??

sounds like u have a cracked head /block. both of which r a pricey fix

run engine get meter for V,has to be 14.5+V.if less replace alternator.

No there is notThe traction control is embedded into theABS Braking SystemIt will, as you found out cut fuel injectors & on somevehicles,fords, slam on the rear brakesIf I had the answer I would put it all over the interneton how to disable itIt is useless in snow & you sometime can't even use the vehiclesThank the Govt for that so called safety featureBy the time those system activate you already crashed& don't need them

Check your hazard flashers , on and off a couple times then check your brake lights. Some times dirt in this switch causes this sort of problem.

call a mobile key guy

Question edited to full make and model. Changed VIM to VIN. Question moved to sub category. help to fix in the link and a video https://www.google.com/search?q=Hhr+radio+reads+no+VIN ..

They usually hammer the screwdriver into the lock and use the screwdriver to turn the lock in place of a key. Of course they forget about the antitheft system, but some just want to release the steering lock so they can get it onto a low loader and strip for parts. Take off all the plastic and replace the lock. It is a job better left to your local dealership because of removing the hardened steel pin some have and some has a special technique for sliding the cylinder out. The Anti-theft may need reprogramming. This might help https://www.google.com/search?q=hhr+replace+ignition+switch ..

linkage problem. This link might also help: https://www.google.com/search?q=2011+CHEVROLET+Why+doesn%27t+it+go+into+reverse+when+put+in+reverse+or+drive+as+well%3F+&ei=da60YN6gKY3Yz7sP27ivqAI&oq=2011+CHEVROLET+Why+doesn%27t+it+go+into+reverse+when+put+in+reverse+or+drive+as+well%3F+&gs_lcp=Cgdnd3Mtd2l6EAM6BwgAEEcQsAM6AggAOgUIABDJAzoGCAAQFhAeUIqdB1imgQhgnIYIaAVwAngDgAGZA4gBniOSAQgxLjI3LjQtMZgBAKABAaABAqoBB2d3cy13aXqwAQDIAQi4AQLAAQE&sclient=gws-wiz&ved=0ahUKEwier6zYz_PwAhUN7HMBHVvcCyUQ4dUDCA4&uact=5

Replace the cam magnet in the front of the engine.

15 foot lbs.

0.9 lbs.

Your vehicle does not have an orfice. It has an expansion valve.

unplug the snapshot and send it back before it does even more damage! and google problems related to snapshot,you will find thousands of similar complaints!

Hi there's this website something like reliable-store and it is very amazing for manual for repairing servicing anything someone on fixya recommended it to m e and I thank him even today They have full manuals and it's verrrrry cheap

Here is a video of the removal of an axle shaft. Basic tools are needed plus a large socket for the axle nut. https://www.youtube.com/watch?v=qD4arlr9jag http://www.fixya.com/cars/t17796741-right_side_cv_axle_replacement_hhr Also a post about cv questions .