Top 20
2008 Chevrolet Silverado 2500HD Questions & Answers
Remote starter comes only briefly and shuts off
www.dieselplace.com/.../340832-factory-
remote-
starter-quits-after-5-sec...
Nov 23, 2009 - 11 posts - 8 authors
On my 2007.5 Duramax, the factory remote has been working fine ... I tried this morning again with the remote starter while sitting in the truck and same thing, turned off ....2008 Silverado 2500 HD CCLB Duramax 6 Spd Allison 4X4 Z71 ... shut off engine", basically its doing it foryou as your not in the truck to ...
check engine light on wont shift
7 posts
Oct 28, 2011
remote start
11 posts
Oct 14, 2008
More results from www.dieselplace.com
www.gm-
trucks.com/forums/topic/114985-factory-
remote-
start-problem/
Jun 12, 2010 - 10 posts - 8 authors
Factory Remote Start Problem - posted in 1999-2006 & 2007-2013 ... Sounds like you may have an intermittant code coming in and the dealer should be able to pull it out.2008 Sierra SLT ECSB Z71, Corsa Touring, and GMPP CAI .... the remote start button again the truck WILL shut off and the only way to ...
Burning smell, white smoke - 2014 / 2015 / 2016 ...
15 posts
Jan 11, 2014
2008 Silverado Electrical Issue
15 posts
Aug 19, 2012
Making Factory Remote Start Run Longer
15 posts
Dec 21, 2010
2000 Sierra, Starts Then Dies - Code 1631
7 posts
Dec 4, 2008
More results from www.gm-trucks.com
CTSY fuse keeps blowing
ok have your replaced any bulbs? i have found putting bulbs in wrong or just being a bad light bulb can blow fuses. try replacing all bulbs with new ones. its cheap and it could be the problem
1992 Chevy Silverado K1500 No Power!
first buy a DMM meter ,spend $15 and end working blind.
the battery and alternator are easy to test and for sure loss of any kind of DC power easy to find using the meter (ASK HOW)
K2500 pickup or Suburban???? no told and wiring not the same.
no engine told and that too sets wiring. OMG 6 engines 2 diesel.
elaborate NO POWER< means head lamps dead? what?
and stayed on? means what.?
STEP #1 alternator work , battery NEG LUG OFF FIRST or you will blow the 100amp main fuse. doing this ALL WRONG and if a fuseable link, can be hard to find, as others say, not me.
never ever connect any main battery backwards
or you will blow up very expensive electronics,
best I can tell is first failure was the fuse even those kinda hidden
fuses called Fuseable links.
fuses are first on cars, of head lamps dead and park lamps dead
this is first, head lamps work keyon , or off.
so is first thing to check with DC POwer loss, (NO POWER"?)
if battery is 12vdc then the power is not lost but fuses are blown
for sure. head lamps are a safety devices that work even no key in hand.
the under hood box has a fuse marked Lighting, if blow HL are dead
just below Lighting fuse is battery bus bar fuse. <<< blown?
the only hard thing THIS CAR,is the online books stink
back in 1992 no digital books then so most cars nobody was willing th scan 500page service manuals. (nor me)
so only sparse information exists. (join k2500 real forums? Chevy)\
this truck does have (did new) 4 x fuseable links, 1 for alternator
but only that blown kills alternator and runnining engine battery is not
13. to 15vdc so the battery goes dead fast 1/2hour fast.
below 13vdc the alternator is dead or fuse link ALT is blown
there are more LINKs to blow 3 more.
others kill the cab or engine bay fuse boxes dead
so all boxes must be check for lost of 12vdc raw DC power.
head lamps
parking lamps.
to top the list and more, check all things DC power, even radiol
the list of things dead tells you what fuse box is dead.
hope that helps in any way.
regards.
10/12/2022 4:08:51 AM •
Chevrolet...
•
59 views • 0 helpful votes
E brake stuck on the floor. 1992 silverado
A parking brake (informally known as "emergency brake" or simply "e-brake") is a secondary brake system that uses brake cables to engage the rear brakes rather than the using the hydraulic brake system which actuates both the front and rear brakes. The brake cables are pulled by a ratcheting mechanism inside a cabin which can be a pull lever or a push pedal. In either case the mechanism must be able to release the cable tension. Although rare, a problem in this mechanism could prevent the ratchet from disengaging and in turn keep the parking brake engaged. A much more common problem however is with the cables or brakes themselves. Rust and corrosion that accumulates over time can cause the moving parts to bind and not release from their engaged position. To resolve, the binding parts must be moved back into their original resting position manually and then replaced with non-rusted/corroded parts. In some extreme cases it may be necessary to actually cut through a brake cable in order to release tension and make repairs. You can read more here: https://www.yourmechanic.com/services/adjust-parking-brake-cable
7/2/2022 7:18:39 PM •
Chevrolet...
•
109 views • 0 helpful votes
E break stuck to the floor. 1992 silverado
The parking bake assembly return spring may be broken. Is it possible to manually lift the pedal up while releasing the brake? The cable could be seized not allowing the pedal to retract.
7/2/2022 7:21:27 PM •
Chevrolet...
•
75 views • 0 helpful votes
2013 Chevy Silverado. How to change clock time.
Press the power button. Access the clock via the menu button. Finally press the dash buttons that are located right under each display to set the hour, minute, month, day, and year on the 2013 silverado.
3/22/2022 3:08:26 PM •
Chevrolet...
•
584 views • 0 helpful votes
Can a p1637 and p1638 code cause surging and gradual shut down of the truck
DTC P1637
The powertrain control module (PCM) / engine control module (ECM) uses the charge indicator control circuit, and the generator 2 turn on signal circuit on diesels with dual generators, to control the generator(s). A high side driver within the PCM/ECM allows the PCM/ECM to turn the generator ON and OFF. When generator operation is desired, the PCM/ECM sends a 10-11 volts-volt signal to the voltage regulator via the generator turn on signal circuit. This causes the voltage regulator to begin controlling the generator field circuit. Once the generator is enabled by the PCM/ECM, the voltage regulator controls generator output independently of the PCM/ECM. Under certain operating conditions, the PCM/ECM can turn OFF the generator by turning OFF the voltage on the charge indicator control circuit. The PCM/ECM has fault detection circuitry which monitors the state of the charge indicator control circuit. If the fault detection circuit senses a voltage other than what is expected, the charge indicator will turn ON and this DTC will set. The voltage regulator also contains fault detection circuitry. If the regulator detects a problem, the regulator will ground the charge indicator control circuit, pulling the voltage low. This also causes the charge indicator to turn ON and the PCM/ECM to set the DTC.
What engine is in your truck ?
DTC P1638
The powertrain control module (PCM) uses the generator field duty cycle signal circuit to monitor the duty cycle of the generator. The generator field duty cycle signal circuit connects to the high side of the field winding in the generator. A pulse width modulated (PWM) high side driver in the voltage regulator turns the field winding ON and OFF. The PCM uses the PWM signal input to determine the generator load on the engine. This allows the PCM to adjust the idle speed to compensate for high electrical loads.
The PCM monitors the state of the generator field duty cycle signal circuit. When the key is in the RUN position and the engine is OFF, the PCM should detect a duty cycle near 0 percent. However, when the engine is running, the duty cycle should be between 5-100 percent. The PCM monitors the PWM signal using a key ON test and a RUN test. During the tests, if the PCM detects an out of range PWM signal, DTC P1638 will set. When the DTC sets, the PCM will send a class 2 serial data message to the IPC to illuminate the charge indicator.
1/23/2022 5:20:51 AM •
Chevrolet...
•
1,176 views • 0 helpful votes
2014 chevy silverado immobilized
Hi,
if you performed these tasks and still cannot start the car, please double check that you're using all products from the manufacturer of the car (or affiliated). This type of thing happens with printers...where the main device won't work if it senses any 3rd party or unauthorized components. You can try to call your local dealership to see if your car is built like this. Thank you.
6/3/2022 6:23:57 PM •
Chevrolet...
•
36 views • 0 helpful votes
Not finding what you are looking for?