20 Most Recent 2009 Dodge Ram 1500 Questions & Answers

Driver side,top corner towards the fire wall

Check your Relays 2 of them one locks other one unlocks,

Not considering the costs of parts themselves, the labor to remove and replace the transmission, torque converter and flexplate runs estimates at approximately 4.5 hours. If you have a skid plate and dual exhaust, add another .5 hour. At rates of approximately $80-100 USD per hour of labor, you are looking at $360.00-$500.00 labor, plus the cost of parts and fluids.

check your ball joints and sway bar links

Broken exhaust hangers. Fit new hangers.

Remove Four bolt`s under seat 14 mm or 15 mm hex bolt under plug any electric connect watch out for seat belt .

Question edited for clarity. Question moved to Dodge Ram. https://tighttorque.com/vans/ram/promaster Torque Specs https://www.google.com/search?q=2016+dodge+ram+promaster+city+2.4+cylinder+head+torque+specs Sequence is always centre outwards and crisscrossing to the edges and normally in three tightening passes to the final torque. https://www.google.com/search?q=2016+dodge+ram+promaster+city+2.4+cylinder+head+torque+sequence ..

no ca/truckr model told at all, of many 3 or 4.no engine told and is and engine problem.the VIN digit #8 is the engine codeNO model told.ram 1500 ?, 2500, 3500 or 4000 , and not the Ram van. 1998 (4000 Mexico or Canada)no engine told one is Diesel;, 3.9 L Magnum V65.2 L Magnum V85.9 L Magnum V85.9 L Cummins turbo-diesel I6<<< ill not cover this ever.8.0 L Magnum V10does the starter motor always work correctly every time, called cranking?we get the fact it does not start. sometimesbut what is not clear, at all, is that the starter always makes this sound called cranking? or fails to do crankingsee MP3 post

step1 in the service manual states check levels first then make sure the shift linkage is good end to end, then scan the pcm for TCM errors. using a real scan tool OBD2 USA and more, lots more, check fuses? to the service manual pump; pressure tests PRNDL pressures each?

If you're experiencing difficulty starting your 2012 Dodge Ram, even after replacing the fuel pump, spark plugs, and fuel relay, there may be several other possible causes. Here are a few things you can check:

1. Check the Battery: A weak battery can cause starting issues, especially in colder temperatures. Check the battery voltage and consider replacing the battery if it's not holding a charge or is more than a few years old.
2. Inspect the Ignition System: The ignition system includes the spark plugs, ignition coils, and spark plug wires. If any of these components are worn, damaged, or corroded, it could cause starting problems. Check these components and replace them as necessary.
3. Check the Fuel System: While you've already replaced the fuel pump and fuel relay, it's possible that there is still an issue with the fuel system. Check the fuel pressure to make sure it's within the manufacturer's specifications. If it's too low, there could be a problem with the fuel filter or fuel injectors.
4. Check the Engine Coolant Temperature Sensor: The engine coolant temperature sensor can affect the fuel system and cause starting problems if it's faulty or not reading the engine temperature correctly. Check this sensor and replace it if necessary.
5. Check the Starter Motor: The starter motor could be failing or not engaging properly, which could cause starting problems. Check the starter motor and have it tested if necessary.

If none of these suggestions resolves the issue, it's recommended to take your vehicle to a certified mechanic or dealership for further diagnosis and repair.

Your A/C system have safety switches, IE-limit switches. You could have either low or high pressure kicking out your compressor. You need a set of gauges to tell what your issue is.

The lightning bolt on the dash means that there is a problem with the electronic throttle control system in your vehicle. Get a code reader and scan the engine for any logged codes. The light may be on for a glitch and the electronic throttle control system needs to be reset. To reset the Dodge Ram throttle position sensor(TPS), You need to turn on the ignition without Your foot on the brake, so the engine doesn't start. Then press the accelerator on the floor for 15 seconds. Release the accelerator. Then turn the car off and start the engine and drive.

Partstore knows

Check out the videos. Also drop a bottle of Fuel System Cleaner to a quarter tank of gas. https://www.google.com/search?q=O2+Oxygen+heater+incomplete

Guaranteed To Pass® Emissions System Cleaner, 12 Fl Oz

https://www.crcindustries.com > products > guaranteed-... With a "double your money" guarantee if your vehicle fails the emissions/smog inspection after use, CRC Guaranteed To Pass® is the trusted choice in emissions ...

CRC Guaranteed to Pass Emissions Test Formula, 12 Fluid ...

https://www.amazon.com > CRC-05063-Guaranteed-E... GUARANTEED TO PASS EMISSIONS SYSTEM CLEANER contains powerful detergent additives strong enough to remove harmful carbon and varnish deposits from the fuel ... Rating: 3.9 · ‎2,090 reviews

CRC Guaranteed to Pass Emissions Test Formula CRL 750606

https://www.napacanada.com > CRL750606 CRC Guaranteed to Pass Emissions Test Formula - CRL 750606: Available online or at your local NAPA Auto Parts store.

Question edited for clarity. Wiring diagrams at the bottom of the page. https://www.2carpros.com/questions/dodge-ram-1997-dodge-ram-shift-solenoid-relay https://www.google.com/search?q=2001+Dodge+Ram+truck+transmission+pressure+plug+wiring+diagram ..

maybe try and see if the bulbs are seated firmly in the sockets.

Hello. The positive polarity (+) color wire for the fuel pump on your Dodge truck can be any color except black. The negative polarity (-) color wire is, usually, black. Those 2 main fuel pump wires are a thicker gauge than the other wires. Good luck and keep me informed; if you want to.