20 Most Recent 2006 Hyundai Tucson 2.0 Questions & Answers

I'm blaming you pal ?????? try to locate the issue by having someone run the car out of gear ...whilst look have a look under the bonnet listening for it ... Simulate the conditions ..operate the Air con.. Engine running

Grab a torch and shine it down the front of the engine. It should be easy to work out how many belts there are. However if you are not sure how to do this, it would be better if you get the mechanic to replace them rather than do it yourself.

http://www.obd-codes.com/p0122

P0231 is low voltage at the fuel pump. Could be a bad fuel pump relay, bad wiring in the fuel pump supply circuit, a loose or damaged connector. or a blown fuel pump fuse. If you're able to drive OK then there's probably an open circuit condition in the circuit between a splice in the fuel pump circuit and the powertrain control module. P1187 is an Oxygen Sensor Heater Control Circuit - usually denoting the 2nd bank. That depends on the vehicle. But usually indicates the sensor needs replacement. If you don't have a shop manual it might be best to take the vehicle to a pro who has the proper diagnostic equipment to fix. Good luck.

thrust bearing failing.

if the hose are not leaking and its not the drain plug you need to replace it

There is no fuse for the interior lights. It is likely to be the bulb or the door switch. The second Page link shows locations.

2005 Hyundai Tucson fuse box diagram

StartMyCar https://www.startmycar.com > Tucson > Fuse box 2005 Hyundai Tucson fuse box diagram. The 2005 Hyundai Tucson has 2 different fuse boxes: Engine Compartment diagram. Inner Panel diagram.

Hyundai Tucson (JM; 2004-2009) fuses and relays

Fuse Box Diagrams https://fuse-box.info > hyundai > hyundai-tucson-jm-2... Here you will find fuse box diagrams of Hyundai Tucson 2004, 2005, 2006, 2007, 2008 and 2009, get information about the location of the fuse panels inside ... You've visited this page 2 times. Last visit: 2023-08-01

Hyundai Tucson 1 (ix35) - fuse and relay

FuseAndRelay.com https://fuseandrelay.com > hyundai > tucson-1 It is located in the left end of the dashboard, behind the protective cover. ... The fuses designated as C / LIGHTER or P / OUTLET are responsible for the ... You visited this page on 2023-08-01. ..

The mechanism of a reclining driver's seat in a car can be complex, and it may require specialized tools and knowledge to diagnose and fix the problem. Depending on the cause of the issue, it may be possible for you to fix it yourself if you have the necessary skills and tools, but if you are not experienced with automotive repairs, it may be best to take the vehicle to a professional mechanic. Before attempting any repairs, you should consult the owner's manual for your vehicle to understand the seat mechanism and any safety precautions you should take. If the problem is related to a broken part or a loose connection, you may be able to fix it by yourself with some basic tools. However, if the issue is more complex or requires a replacement part, it may be best to take your vehicle to a professional mechanic or an authorized Hyundai dealership for repair. They will have the expertise and experience to diagnose the problem and repair the seat mechanism correctly and safely.

The problem is with the fuel system or possibly the fuel pump. Try checking the fuel pressure and ensuring enough fuel gets to the injectors. If the fuel pressure is adequate, but the injectors are not pulsing, you may need to replace them or have them professionally cleaned. If the fuel pressure is too low, then check the fuel pump and its related components

https://www.mahle-aftermarket.com/media/local-media-north-america/pdfs-&-thumbnails/torque3.pdf

https://www.youtube.com/watch?v=u1IA6hgM40E Seems like they have a lot of problems. This video may help you.

Tucson has this notorious problem. The door locks operate using a steel cable, just like the clutch cable of most of the motorcycles. This cable stretches out with time and eventually, the throw of the lock (the range of motion) would not be enough to pull the cable sufficiently and unlock the cars. On youtube, you'll find some fixes which basically suggest to cut the stopper in the lock mechanism to increase the throw length of the lock latch.