20 Most Recent
2007 Jeep Compass 2.0 Questions & Answers
Where is horn relay on a 2010 jeep compass
I need help on my 2010 jeep compass 2.4l the horn does not work I put a new horn in it worked for a couple of days and stopped working. Any one know if there's a fuse for the horn I can not find one ?
2/19/2018 10:31:20 PM •
2007 Jeep...
•
Answered
on Feb 19, 2018
2007 Jeep Compass
If your check engine light is flashing, it indicates there's a relatively serious problem detected by the ECM - continued operation is not recommended. Have you had the codes read? Not many technicians are willing to guess at what may be wrong without more information than you provided. Post your question again and state what codes you have stored in the ECM. Or you can look the codes up yourself once you know what they are. Or, (recommended solution) take it to a qualified technician and have them troubleshoot it, provide you a recommendation for repairing it, and an estimate.
4/6/2017 8:16:13 PM •
2007 Jeep...
•
Answered
on Apr 06, 2017
Changing an oil pan on 2007 jeep compass
Easy ,.there may be something in the way of getting it out.,.but if you can sneak it out just, drain oil ., remove the oil pan bolts.,. Remove old pan and all gasket material clean surface., replace new oil pan and gasket. Tighten bolts in a circular pattern till snug then tighten in a star like pattern I kinda understand
1/10/2017 10:45:03 PM •
2007 Jeep...
•
Answered
on Jan 10, 2017
Not all the time but when I start the car it starts very hard. When it starts hard like that and I wait a few second and put it into gear it slams into gear and sometimes won't move.
get it serviced?
hard starts are usually never getting a tuneup, (like spark plugs?)
slamming in to gear is normal if RPM is too high in park, is it.
wont move , in any gear, car wont move even in reverse.
and RPM of engine does what , sticks low, like 800 rpm
or screams at the advancement of right foot.
need lots of details. we cant drive car, but if could in 5min flat all that is clear,
eg:
transmission slips
engine weak
engine racing in park too high.
wont start and misfires when it does.
is fuel fresh, not year old.
ever get a new air filter and fuel filter. if filter is outside tank.
4/22/2015 7:07:32 PM •
2007 Jeep...
•
Answered
on Apr 22, 2015
Intermintlly get these codes u110a, b1a28, u0126, u0141, u0151, no power, trans feels like it slips.
on the dash cluster display, sure.
these are not good codes to get..
what is best is the use a real OBD2 scan tool , and for sure
one the reads extended chrysler codes.
first U110a
U110A is a steering column control module lost communication
if you want to read the FSM on these codes, you can
and do all the tests it states there, to find true cause.
do you, , if not get the car scanned by a mechanic and diagnosed.
B1A28-ECM Mismatch With Skim
126. lost comms with steering angle sensor
141 lost comms with TIPM
151 lost comes with occupant restraint system.
the B1a28 is very serious. or just a loose connector.
the ECM and SKIM say the VIN number is lost. or was garbled
in the comm.s (noise)
3/22/2014 3:39:11 PM •
2007 Jeep...
•
Answered
on Mar 22, 2014
Horn just starts blowing for no reason
security.
read the operators guide (lost? it?) on security.
or for IMMO, (immoblizer)
the guide shows you how to find which switch tripped the alarm.
if no reason, then the horn relay is bad.
on this car and all 2007 and newer CAN-BUS Jeeps,
you need a full scan, of the whole car.
the newer cars have a huge list of checks it does.
and will report , in DTC errors.
read the FSM if you want to do DIY.
or login to alldata.com and read.
see the tests there.
2/15/2014 3:13:45 PM •
2007 Jeep...
•
Answered
on Feb 15, 2014
How do i remove drivers side door panel on 2007
There are panel removal tools available, but any flat prytool will suffice to pry panel away. There are also screws located at the actual door pull/handle area to remove. after loose, panel must be raised vertically as the top trim/rubber will be hooked @ window opening. there are also wires to be watchfull of and clips to disconnect before panel will be successfully pulled away. Reinstall is just the reverse procedure.
9/25/2013 12:32:30 AM •
2007 Jeep...
•
Answered
on Sep 25, 2013
Air vents
On most models built after 2000 the blend doors are operated by small electric motors. The doors would need to be checked.
7/20/2013 7:57:35 PM •
2007 Jeep...
•
Answered
on Jul 20, 2013
Not finding what you are looking for?