Top 20 2007 Toyota Hilux 2.7 Questions & Answers

I think you should try this website big-manuals . It helps you repair your vehicle easily without more help. Ask the girl in chat at the bottom of the page

Should be inside the fuel tank. Drop the tank or lift the bed to gain access.

Take it back to the shop that did the work. It should run completely fine.

Here are the torque specs you requested: MAIN BRG CAPS= 29FT/LBS THEN TIGHTEN AN ADDITIONAL 90 DEGREES in sequence(two step process) ROD BEARING CAPS= 18 FT/LBS CYLINDER HEAD BOLTS= 29FT/LBS + 90 degrees + another 90 degrees in sequence from the center out ward, (3 step process). Please let me know if you have any questions

The fuel sensor is to blame - need to locate it and replace.

How long has it been ran since new battery installed ?

you should check your wires make sure they are tight and that they are in good condition you could also check your alternator and make sure it is working properly and check your fuses and make sure none are blown.

Please define. You may have blown a fuse link.Jecking?

you will get these from a toyota dealer from their workshop cd manual. However if you want to check the chassis for bends , the dimensions do not need to be known place the vehicle over a flat floor and using a plumb bob on a sting line drop points onto the floor and mark the position on the floor . Use the same points on each side of the chassis get as many marks on the floor as possible and put on the floor next to the mark where they came from on the chassis (ie rear spring hanger, foot step bracket , tank bracket etc) move the vehicle out of the way and with a tape measure measure the diagonals of like points. Write the dimension on the floor on that diagonal. When finished the variations of like diagonals should be no more than 3mm max. The diagonal with the largest variation will indicate exactly where the chassis needs straightening

Valve setting? Most engine valves have an automatic adjuster to self adjust the setting. You didn't say you had it apart. So, I'm thinking you have a dirty condition that would make the adjuster or valve tap. If so good additives just for both those conditions can restore the adjusting by cleaning and freeing the ailing parts. Try the link below for more info and needed product. Stops noisy engine valve tap in 10 minutes or free Add Driving ends tap

please give me your immobiliser or alarm system info .if is immo system problem when you turn on switch meter will no come out check engine light ,please check it.

2007 2.7L hilux what country is this car, (1million posts and not 1 said yet) this is USA forum. Seventh generation (AN10, AN20; 2005-present) 2.7 L 2TR-FE I4 engine. Gas too. go to your country Toy dealer and ask for the factory service manual read the ignition chapter, and wiring chapters bingo. or online books dont have your car, only usa spec cars. here. or join a toy forum in your country is a win, big time.

Because there is a;ways an explosion danger, I would not go there. Just ask a Toyota certified repair centre to solve the problem. You never know what is wrong. Check your manual, if the airbag can be switched off, when you have a baby on the passengers seat. Perhaps that is the problem.

same same but there are a few different ratios available depending on your engine and transmission.

Gidday, your best bet would be to take it to a mechanic, could be a bearing, the cable, the clutch, some times there is a rubber bush that could get a little sticky at the pedal, try pressing it with the engine off and see if it's still making the sound.

Normally it would be open/short But you should check the injector circuit from the ECU (Engine Control Unit)

check your plugs , ck your injectors ,ck your wires too , should be one of the 3

its 1 of 2 things. 1: the fuel is low, use a dip stick, if gauge reads ok. 2; or the tank sender is bad, but gauge reads wrong. 3: the guage wire is disconnected, cut or corroded connections.

in front bumper' read the FSM and all warnings there, no read it twice.

I'm assuming that you followed the lamps advice and replaced the timing belt. This indication comes on automatically every 150000km to remind you to replace the timing belt before it breaks and causes catastrophic engine damage. That being said, here is the procedure to reset the lamp for the next time.