20 Most Recent 2005 Toyota Sienna Questions & Answers

Have 2005 Sienna and its Driver side door was not openning. Cheap dealer fixed it himself in front of me. After opening the doors plastic assembly while sitting inside with a screw driver. Then he bent the clip towards left where the metal wire is connected. If you guys want to see what he did i would record a video and upload for you guys. Let me know at xahid2000@yahoo.com

2005 Toyota... | Answered on Apr 14, 2019

Hello Ravendra, Engine timing, RPM and fuel trim and many other factors are generally controlled by the ECM (engine control module) which could also be referred to as a PCM (power-train control module) so manually adjusting or setting ignition timing is not possible on modern day vehicles.

2005 Toyota... | Answered on Jan 06, 2019

Most likely the problem is the lower steering knuckle. This is the one outside of the firewall, under the vehicle and it hooks up to the power steering assist cylinder. In my opinion the knuckle has to work at an unreasonably steep angle and this compounds the problem. The knuckle (especially in salt areas starts to corrode and becomes hard to turn. Toyota says the water gets into the bearing and they beings to rust the bearing and turning the whell starts to feel stiff. I have this problem and I sprayed liberal amounts of a rust inhibitor that a local place uses to rust proof cars (They sell small spray bottles of it for $5). They are called OIL TECH in Barrie, Ontario and make up their own formula. The formula has addatives that breaks the surface tension on the oil treatment and gets it into the tiny cracks and crevices on your vehicle. I sprayed this all over the knuckle, turned it back and forth a couple of times and continued spraying. I let it sit for an hour and went for a test drive -- problem solved. You could actually see the rust on the exposed parts of the knuckle. I probably will have to do this once every month of two but what the heck. It is a lot cheaper than having to replace the steering shaft ($1000+???) Probably other types of rust proofing or lubricating oils will work. I long for the old days of grease fittings and you never had to replace ball joints and tie rod ends etc.

2005 Toyota... | Answered on Nov 09, 2017

After removing the pinch bolt and nut it is usually necessary to tap in a small chisel or large screwdriver to open up the slot sufficient for removal. Sometimes burrs hold components together and sometimes there is a corrosion bond so a squirt of penetrating oil is a good idea too.

2005 Toyota... | Answered on Jun 17, 2017

The transmission is not shifting properly

2005 Toyota... | Answered on Feb 17, 2017

video on you tube

2005 Toyota... | Answered on Nov 01, 2016

check the switch in the glove compartment

2005 Toyota... | Answered on Nov 06, 2015

Sorry, there isn't a clock fuse. It is very low voltage and amperage. It is powered by another computer. The clock just died.

2005 Toyota... | Answered on Apr 04, 2015

3 bolts under the hood. one in the door jamb. four under the car behind the wheel well liner. One at the very front of the side skirt underneath.

Read more: http://www.xcardiag.com/

2005 Toyota... | Answered on May 08, 2014

Go to AutoZone, Advanced Auto Parts, or NAPA to use their Diagnostic Code Reader and get codes and they will tell you problem and parts needed to repaird.

2005 Toyota... | Answered on May 08, 2014

What kind of codes?

2005 Toyota... | Answered on May 07, 2014

Not finding what you are looking for?
2005 Toyota Sienna Logo

Popular Tags

70 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Toyota Experts


Level 3 Expert

85219 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sienna Toyota

  • Sienna Toyota

Most Popular Question

2005 toyota sienna van power steering

  • Cars & Trucks