2007 Chevrolet Chevrolet Silverado 1500 - Page 8 - Answered Questions & Fixed issues
Need an emissions schamatic for my 1984 Chevrolet k10 350 engine with California emissions
Finding an emissions schematic for a specific year, make, model and location of a vehicle can be difficult. The best place to find a emissions schematic for your 1984 Chevrolet K10 350 engine with California emissions would be to check with the following sources:
- Chevrolet dealership: Contact a Chevrolet dealership that specializes in older models. They may have access to emissions schematics for your specific vehicle.
- Auto repair shop: Visit an auto repair shop that specializes in emission systems. They may be able to provide you with the information you need or help you find the right schematic.
- Service Manual: You can try searching for a service manual for your specific vehicle, which would include information on the emissions system.
- Government website: Check if your local government has any specific regulations regarding emissions for vehicles of your age, model and location, and see if there is any information on their websites or publications.
- Online forums and communities: There may be online forums or communities dedicated to specific makes and models of vehicles where owners and mechanics share information and resources, including emissions schematics.
Keep in mind that these resources may not have the schematic you are looking for and it may be challenging to find such specific information for a vehicle of that age.
Hi im looking for the location of my transferer case control module.on my 98 chevy tahoe 4x4 and how to easy removed it
The transfer case control module on a 1998 Chevy Tahoe 4x4 is typically located under the driver's side of the dash, near the steering column. To remove it, you will need to first locate the module and then disconnect the electrical connectors. Then you will need to remove any mounting bolts or screws that are holding the module in place. Once those are removed, you should be able to gently pull the module out. It may be helpful to consult your vehicle's service manual for specific instructions and diagrams to locate and remove the module. It is also recommended to get it check by a professional mechanic, as the problem might be other than the module itself.
2000 chevy e3500 drl location
DRL location ? Module ? Lights ?
The operation of the daytime running lamps is controlled by the daytime running lamps control module. The module is powered by CKT 39 (PNK) from the GAUGES fuse, and it is grounded through CKT 150 (BLK). The module turns on the daytime running lamps under the following conditions:
Daytime Running Lamp (DRL) Control Module
Under the left side of the IP, taped on the IP harness
My 2003 Chevrolet ASTRO van the front heat works and blows fine but the rear heater blows cold only
There could be a few possible causes for the rear heater not blowing hot air in your 2003 Chevrolet ASTRO van. Here are a few things you could check:
- Make sure that the rear heater control valve is fully open. This valve is located near the heater core and controls the flow of coolant to the rear heater.
- Check the coolant level in the radiator. If the coolant level is low, the heater may not be able to produce hot air.
- Check for any leaks in the coolant system. If the system is leaking, it may not have enough coolant to produce hot air.
- Check the thermostat. If the thermostat is stuck closed, it may not be allowing enough coolant to flow through the system to produce hot air.
If these steps do not help, it is possible that there is a problem with the heater core itself, or with other components of the heating system. It may be necessary to have a mechanic diagnose and repair the issue.
My 1989 Chevrolet S10 4.3 starts fine but after 15 or 20 minutes of it running it will flood out if I disconnect one of the injectors it will crank up and run
It sounds like your 1989 Chevrolet S10 may have a problem with the fuel injectors or the fuel system. When you disconnect one of the injectors and the engine starts, it suggests that one or more of the injectors may be stuck open and flooding the engine with fuel. This could be caused by a malfunctioning injector, a problem with the fuel pressure regulator, or a
Here are a few things you can try to troubleshoot the issue:
- Inspect the fuel injectors for any signs of damage or malfunction. The injectors may need to be cleaned or replaced if they are not functioning properly.
- Check the fuel pressure using a fuel pressure gauge. The fuel pressure should be within the manufacturer's specified range. If the pressure is too high, it could be caused by a faulty fuel pressure regulator.
- Replace the fuel filter if it is clogged or dirty. A clogged fuel filter can restrict the flow of fuel to the engine and cause starting and running problems.
- Check the control panel for any error codes or messages that may indicate the cause of the issue.
What is the diameter of a freeze plug in the block on a 6.0 Chevrolet Escalade motor
The diameter of the freeze plug in the block of a 6.0 liter Chevrolet Escalade motor is approximately 1.75 inches. However, it is important to note that the size of the freeze plug may vary slightly depending on the specific model and year of the vehicle. It is always best to consult a repair manual or the manufacturer's specifications for the exact dimensions of the freeze plug in your particular vehicle.
Can I replace a 5 speed transmission with an automatic transmission for a 1992 Chevrolet ck 1500
It is generally not possible to replace a manual transmission with an automatic transmission in a vehicle. This is because the two types of transmissions have different internal components and use different methods of transmitting power from the engine to the wheels. In order to replace a manual transmission with an automatic transmission, you would need to make significant modifications to the vehicle's drivetrain and possibly to the engine as well.
Additionally, the cost and complexity of such a conversion would likely be much higher than simply replacing the existing transmission with a new manual transmission. In most cases, it is more practical to repair or replace the existing manual transmission rather than attempting a conversion to an automatic transmission
Do I need to get a garage reset .
It is possible that the warning light is still on because there is an issue with the fuel system that has not been resolved. Bleeding the water from the fuel filter and changing the filter itself may not necessarily fix the problem, depending on the cause of the issue.
If you have already tried disconnecting the battery and the warning light is still on, it may be necessary to have the car diagnosed by a mechanic to determine the cause of the problem. The mechanic may need to use diagnostic equipment to read any fault codes stored in the car's computer system, which can help identify the problem. Once the issue has been identified, the mechanic can advise you on the necessary repairs and whether or not the warning light will need to be reset. It is generally a good idea to have a professional mechanic diagnose and repair any issues with your car, as attempting to fix problems yourself can be risky and may cause further damage if done incorrectly.
2012 chevrolet traverse 3.6 what reads the rpm signal and from there how does the tachometer read it
Tachometer
The IPC displays the engine speed as determined by the ECM. The IPC receives a serial data message from the ECM indicating the engine speed. The ECM transmits the engine speed to the body control module (BCM) via the serial data circuit. The BCM then transmits the engine speed to the IPC via the serial data circuit. The tachometer defaults to 0 RPM if:
• The ECM detects a malfunction in the engine speed sensor circuit.
• The IPC detects a loss of serial data communications with the BCM.
• The BCM detects a loss of serial data communications with the ECM.
Well seats for me 01 Tahoe fit a 97 Tahoe
ask chevy that? USA spec,car not told.
i bet not but ask them.
or ask and auto wrecker this, they have to tools to do that .
they have to fit and work, right, seat heater or seat motors
and those very tricking SRS air bag , person sits on seat, weight sensors, why not ask them.?
no RPO tag list posted by you
the RPO list is and AS BUILT list, and seats too, bags, belts and all.
Not finding what you are looking for?