20 Most Recent
2007 GMC Yukon Questions & Answers
2007 GMC YUKON 5.3. LOCATION of EGR VALVE please?
Question edited for clarity. Did you know typing in CAPS is considered shouting, plus it is harder to read.
Question moved to model category.
The EGR valve is located in the engine compartment (underneath the hood). Most engines require exhaust gas recirculation to meet emissions standards.
2007 GMC Yukon. The liftgate does not open.
Something has likely fallen between the top of the liftgate and the cab. It will be the space above the seal. Use a clothes hanger or something similar to remove the obstruction.
The radio won't go off on my 07 Yukon when I turn off the engine and open the door
Do courtesy lights come on and go off when you open and then close the drivers door?
if courtesy lights work as expected then the BCM is communicating properly with the door control module, i.e. it knows the door was opened and closed, so likely the problem is between the the BCM and the radio (low speed comm bus) or the radio itself.
A scanner capable of presenting the BCM, door control module, and radio states will likely be required to determine the fault location.
is the CEL/MIL indicator lit?
2007 GMC Yukon starts and running but it's smoking white smoke and over heated what will it take to fix it??
a repair shop NEAR you. If it is smoking and has overheated you HAVE a damaged engine. The more it is driven the worse it will be. Really you should probably get it towed to a shop. Most repair shops can work on it, all of them are going to make some $ off this, as probably minimally a blown head gasket, but likely rod or piston damage. Make sure the coolant is full before you try and drive it anywhere. treat it gently... maybe it will get to the shop under it's own steam if it is close. The only next step is engine seizure... and new engine time. (rebuilt dropped in might be $2000 if you're super lucky)
Removal of headlight assembly to change headlight
I am not familiar with the model but the vehicle handbook usually contains instructions and diagrams on bulb replacement. If stuff has to be removed to change the bulb the book will usually tell you to take the car to your nearest dealer.
Many headlamp bulbs need a strong light, a mirror and a great deal of patience...
2007 yukon headlight wont turn on
Odds are you have a connection problem. Stop & buy a tube of dielectric compound from an auto parts store. Apply it to the electrical connection at the lamp after you make sure there is no corrosion present.
Dome Lights
The interior light module is not timing out. The possibility of the interior lights staying on could run your battery down over night. Replace the interior light module.
2007 GMC Yukon wont start....
Ok supper Dave , let's get this stright , when you turn the key to start the vehicle , what happens ? The starter spins the engine or doesn't spin the engine ? This would be a no crank no start condition . if the engine does spin an doesn't start an run this is a crank no start condition . Now which is it ? The factory radio is hooked to the serial data communication network , did you or who ever installed the aftermarket radio use a interface module ? Are you familiar with the electronics on this vehicle ? BCM - body control module , low current inputs from the ignition switch which determine what mode to put the vehicle in ?
Case 4 Data Bus Issues
The body control system consists of the body control module (BCM), communications, and various input and outputs. Some inputs, outputs and messages require other modules to interact with the BCM. The BCM also has discrete input and output terminals to control the vehicle's body functions. The BCM is wired to the GMLAN high speed serial data buss and the GMLAN low speed serial data buss and acts as a gateway between them. If the BCM does not communicate the vehicle will not start due to the inability of the engine control module (ECM)/powertrain control module (PCM) and theft deterrent module (TDM) to communicate without the BCM providing the gateway function.
Power Mode Master
This vehicles body control module (BCM) functions as the power mode master (PMM). The ignition switch is a low current switch with multiple discrete ignition switch signals to the PMM for determination the power mode that will be sent over the serial data circuits to the other modules that need this information, and so the PMM will activate relays and other direct outputs of the PMM as needed. Refer to Power Mode Description and Operation for a complete description of power mode functions.
Sorry but I am a GM Tech . have been for over thirty years , Cadillac , Buick an Chevy .audio buds think it's something else. Your audio buds don't have a clue ? When change something you better well know what your messing with. .
Cant get the spare tire
Probably the cable it is stuck,you are going to need help from a mecanic,or try to pull down the tire with your ands,lift the car and put jack stands so you can have more space.
Do oil sending units have history of leaking?
An Oil Pressure Sensor/Switch is just that, a 'pressure sensor', and yes they do have a leak history. It may sometimes leak from the threaded area that it is installed by, and in most cases can easily be fixed by tightening it a little (use caution to not strip the threads in the block or breaking it off, if that happens then you have even more problems). Otherwise a leak may be from the switch mechanism itself, if so then it is best change it right away and it is actually very easy to do so. Remember it is a a 'pressure sensor', so if it is leaking that means it can easily become a stronger leak, to include a total leak, meaning pumping oil out of the engine at the range of 40-60 PSI.
Not finding what you are looking for?