20 Most Recent 2007 GMC Acadia SLE Questions & Answers


first if you are changing the bulb only and it is a HALOGEN
there is a round acess hole in the inner fender remove it and change the bulb
if you have HID lights or are changing the head light assembly then you have to remove the front bumper facia
hope this helps
hope you have HALOGEN lights

2007 GMC Acadia... | Answered on Jul 30, 2018


Try disconnecting the battery cables for about 5 minuites. I don't know why you needed to recharge the battery but you might have crosses something or created a short. Disconnecting the terminals will help reset the computer as well as any tripped saftey relays or sensors. Good luck let me know how it works out.

2007 GMC Acadia... | Answered on Jan 07, 2018


Do you have an aftermarket alarm or other system hooked up to the ignition system?

You need to provide the specific year, engine size, and model Acadia as well, such as if it is an LT or not for a proper diagram. Even with a wiring diagram, it's going to be a needle in a haystack that you will be looking for.

This sounds like you have some sort of aftermarket system that has a relay or capacitor that is delaying the cut off to the switch, which will explain the delay in shutting off and the drain on your battery.

Here's a test I would start with to see if you can narrow things down...

Remove the positive cable and hook a test light between the post and the positive cable and the test light will light up. Go to your fuse panel and pull each fuse one at a time and replace it, going from one to the next until the light goes out. That will be the circuit that is causing the drain. Hopefully you will be able to isolate the offending device, and hopefully correct the back feed into your ignition system at the same time.

2007 GMC Acadia... | Answered on Dec 09, 2017


Power or manual? If manual most common problem is the touch pad switch.

2007 GMC Acadia... | Answered on Aug 24, 2017


Brown wire is not for data , for ign. voltage . in run or acc. Red white wire gets it's B+ voltage from PWR MOD fuse 2 amp. I/P fuse box . Having the system check for DTC'S diagnostic trouble codes is the first step in diagnosing a no start .
DTC B3006
DTC B302A
DTC B3031
DTC B3055
DTC B3060
DTC B3935
DTC B3976
DTC P0513
DTC P0633
DTC P1631

Diagnostic Starting Point - Immobilizer
Begin the system diagnosis with the Diagnostic System Check - Vehicle. The Diagnostic System Check will provide the following information:
• The identification of the control modules which command the system
• The ability of the control modules to communicate through the serial data circuit
• The identification of any stored diagnostic trouble codes (DTCs) and their status
The use of the Diagnostic System Check will identify the correct procedure for diagnosing the system and where the procedure is located.

There should be a dark green wire also ,at the theft module . This is for data communications , low speed GMLAN . Do you know what GMLAN is ? GM's version of C.A.N - controller area network . If your missing this wire , no wounder it won't start .
Theft Deterrent Control Module Pin
Wire
Circuit No.
Function
1
0.35 RD/WH
1040
Battery Positive Voltage
2
0.35 BN
4
Ignition I/II Voltage
3
0.35 BK/WH
1551
Ground
4
--
--
Not Used
5
0.35 D-GN
5060
Low Speed GMLAN Serial Data
Your best bet ,take it to the GMC dealer , there is no way to by pass this .

2007 GMC Acadia... | Answered on Aug 19, 2017


2007 GMC Acadia manual liftgate will not open. Is there a way to bypass the electronic switch to get it open and replace the switch or latch?

2007 GMC Acadia... | Answered on Feb 26, 2017


On this website (link below) you find fuse box diagram and description for GMC Acadia First Generation

GMC Acadia mk1 First Generation 2007 2008 fuse box diagram Auto Genius

2007 GMC Acadia... | Answered on Nov 01, 2016


{: ) The driver door switch is also the master switch for all 4 windows. If only the driver window is not working, but the other 3 can be controlled by the master switch, then you need to focus only on the driver window circuit itself. If a scan tool is not available, you can diagnose it in a conventional manner. You will need to remove the driver door trim panel so you can test for voltages on the window motor which only have two wires. The driver window motor receives its power directly from the driver door switch which is protected by a circuit breaker. So there's no small fuse issue here, and you really can't one. The circuit breaker is very unlikely the cause.
If there is voltage present on the motor terminals as you move the button up or down, it is possible that the motor got stuck ( if not busted), or a cable is loose, or a rail that is binding.

2007 GMC Acadia... | Answered on Feb 20, 2016


You will need to remove the screws from the fuse block then pull it out. Unplug wires and install your new one

2007 GMC Acadia... | Answered on Jan 03, 2016


No they haven't. It probably just has a bad amplifier. It is locataed directly above the parking brake pedal. I would check to see if you have a water leak there.

2007 GMC Acadia... | Answered on Oct 26, 2015


This usually means that the ac is low on charge or the temperature is to low outside for operation.

2007 GMC Acadia... | Answered on Oct 26, 2015


the starter is in the front of the engine right behind the oil filter. Look down at the oil filter and towards the driver side. You have to remove the front cat converter to gain access.

2007 GMC Acadia... | Answered on Oct 25, 2015


GMC Acadia no heat coming from heater Questions ... - Fixya

www.fixya.com > ... > Cars & Trucks > GMC
GMC Acadia cars & trucks no heat coming from heater questions and answers. ... on my GMC Acadia 2008 SLE the panel where i control the AC/Heater stopped ...

2007 GMC Acadia... | Answered on Sep 09, 2015


I can't remember exactly. but I know some gmc have behind front passenger wheelwell others are back seat.

2007 GMC Acadia... | Answered on Jul 13, 2015


Most of them are on the firewall near the top, cowl area. You could also look in the fuse block, they are labeled on the lid.

2007 GMC Acadia... | Answered on Jul 13, 2015


Bottom right side next to glove box, Remove panel just right of glove box.

2007 GMC Acadia... | Answered on May 17, 2015


Address the 'Check Engine' light first. The Stabilitrak message is usually just a symptom of the Check Engine light turning on.

2007 GMC Acadia... | Answered on May 05, 2015


check the ground wires to the rear lights sometimes the head lights will provide backfeed ground when off but cannot when on this would explain the rapid flash

2007 GMC Acadia... | Answered on May 02, 2015

Not finding what you are looking for?
2007 GMC Acadia SLE Logo

390 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2009 GMC Acadia
2009 GMC Acadia

163 Questions

2010 GMC Acadia
2010 GMC Acadia

37 Questions

2011 GMC Acadia
2011 GMC Acadia

48 Questions

2013 GMC Acadia
2013 GMC Acadia

10 Questions

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Acadia GMC

  • Acadia GMC

Most Popular Question

thefuel relay switch 2007 gmc acadia

  • Cars & Trucks
Loading...