20 Most Recent 2007 Hyundai Tucson Limited Questions & Answers

*If you have ANY doubts or worries about working on your vehicle get a good mechanic to do it for you.* Why do you think the wires have been switched? Has the vehicle been serviced recently? That would be the only reason the wires would have been removed. Is yours the 2.7 V6 engine? Spark plug leads are usually different lengths to go to specific spark plugs so leads 1 and 3 will be very different lengths. That means the switch probably hasn't happened at the spark plug end. Check the connections at the other end of the plug wires, at the coil pack end? This is a lot easier to get to and a lot less work.

With your key in the ignition, do not turn it, open the fuse panel by the drivers side door, pull out the 30amp P/CONN fuse at the very bottom (mine was in a weird yellow casing) then plug it back in. The disk drive of the radio should make a noise. Now start your Tuscon and turn on your radio.

Hello! You can search replacement part on eBayHere link for example https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2050601.m570.l1313.TR0.TRC0.H0.Xtucson+2007+air+con+swich.TRS0&_nkw=tucson+2007+air+con+swich&_sacat=0

pull off the bottom hose

Maybe its the electric motors and switches ,worth checking

If EGR temp not correct try cleaning it maybe its gunked up and not giving a correct reading.

The adjustment is made at the handle under the console: ADJUSTMENT OF PARKING BRAKE STROKE 1.Pull the brake lever with a force of approx. 196 N (20 kg, 44 lbs.) and check the number of clicks. Parking brake lever stroke (Standard value) : 8 clicks 2.If the number of notches is not the standard value, adjust the cable length with the adjusting nut on the equalizer. 3.The indicator light will go out when the brake lever is fully released, and will light up with the lever pulled one notch. If it does not operate properly, replace it. 4.After the adjustment, check that the rear brakes do not drag with the parking brake lever released.

remove fuse so as not to discharge the battery for the meantime and replace radio unit later

you will need the code . if you have you have your manual the factory code will be in it on a separate paper probably! could also be in your radio instructions! if you dont have these books you need to go to a hyundai dealer . does it come on and then go off ? if no lights at all in the screen it could be a fuse ! that is also in the book .if no book there are a number of sites on the web that will give you the layout of where they are, and which one is your radio fuse. hope this helps, and i am sorry i cant be more specific good luck,regards terry

You can drill small hole just be careful how far down you drill.

Most engines..... - there will be a hose from the top of the radiator to the top of the engine. - The engine end will have a fitting held on by two bolts. - The thermostat will be under that fitting.

How to disable DRL (Daytime Running Lights) - TucsonDrivers.com

tucsondrivers.com/viewtopic.php?t=1809

Oct 17, 2006 - I wonder why Hyundai didn't put it on the US models? ... I wish my Tucson had daytime running lights. ... The DRL module on the Tucson in Canada basically puts 12 volts on ... #8 Postby Hermine » Wed Jun 20, 2007 5:39 pm.

Daytime Running Lights (DRL) not working =( - Hyundai Forum ...

www.hyundaiforum.com > ... > Vehicle Line Up > Hyundai Accent

Apr 25, 2008 - Join Date: May 2007 ... Basically, I've noticed my DRL are no longer working. ... Does anyone know what does the DRL module looks like and where I could find it? ... 04 Daytime running lights, CaptAthlon, Hyundai Elantra, 9 ...

For intake manifold, my info says 14--15 ft lbs

Starting inside and witg a crossing bolt pattern.. 25 ft lbs If you need further help, reach me via phone at https://www.6ya.com/expert/chris_b82b45c59bcf133d

check the battery connections particularly to the chassis.