20 Most Recent 2007 Dodge Ram 3500 Quad Cab Laramie Questions & Answers


Does this include the outer tie rod nut also to be 45lbs foot torque?

2007 Dodge Ram... | Answered on Jun 16, 2018


The 'WD' stands for 'Water Displacement', was it wet? Penetrating oil is the correct item to use.

Take a look at these videos

2007 dodge 3500 replace rear rotor Google Search

2007 Dodge Ram... | Answered on Feb 11, 2018


If it runs fine when fully warm, replace temperature sensor.

2007 Dodge Ram... | Answered on May 26, 2015


The high mount brake light gets its own signal from the brake light switch (on the brake pedal). Or at least the wire leaving the brake light switch will splice, one wire to the high mount brake light, and the other for the rear brake lights is routed through the turn signal switch, and coordinated there with the turn signal wires to the rear brake lights. The brake wires and turn signal wires share the same wire, and same filament in the bulbs. It is kind of complicated, but brakes applied with no turn signal, brake light wire goes from brake light switch through the turn switch and out to the bulbs. If brakes applied with turning signal, non blinking brake light wire goes from turn switch to rear light, while the turning signal wire will go through the flasher relay, and then to the rear light to cause blinking.

I hope that makes sense. It appears the problem may be in the turn signal switch for both the turn signals and the rear brake lights.

2007 Dodge Ram... | Answered on Mar 15, 2015


In Owners Manual--If You Don't Have One, They Can Be Obtained From Dodge Dealer (parts department)

2007 Dodge Ram... | Answered on Feb 18, 2015


In the fuse box under the hood .

2007 Dodge Ram... | Answered on Feb 11, 2015


OK I have one of these trucks and those hubs are a pain in the buttt big time. Tried changing an axle joint but couldn't get the hub off. Finally after 2 days gave up and took the truck to the dealer. I watched them take it apart. There is a special tool. Put the four bolts back into the hub from the axle side. They should all be loosened but not out of the hub. Take a deep socket that fits the bolt head. Fill the socket with nuts so that you can just fit the hub bolt head in it too. with the axle on stands and both front wheels in the air, the socket on one of the bolts. ( not sure how to get the socket to stay on, maybe a few wraps of tape around the head of the bolt) start the truck and turn the wheels, lock to lock. Get out move the socket to another bolt on the other side and repeat. when youve done all four bolts this way , take all bolts a few turns ( equal distance) and repeat the process. The hub will be pressed out by the socket pushing against the axle tube. At least that's what they did at the dealership.Good luck. Let me know how it works.

2007 Dodge Ram... | Answered on Feb 11, 2015


Since they are OBDII codes, simply google them to find out

2007 Dodge Ram... | Answered on Aug 15, 2014


pulling a motor is the last resort so can you give more information as to why this motor is a lemon. To often I read on this site advice from repair shops that say" better get a new motor or gear box " simply because they see a punter in view and a quick buck.. You say that you are not rolling in cash so the next motor may not be much better than the one you have . So if you have the time to write in the comment box tell us what is making it a lemon and be guided by any advice you receive as it may surprise you as to what the fix may be

2007 Dodge Ram... | Answered on Mar 28, 2014


Get a test light probe so you can see where power is getting to starting at the fuses under the hood. All the fuses there should have power getting to them even with the engine off.

2007 Dodge Ram... | Answered on Feb 18, 2014


It is very unlikely that the transmission would over heat enough to cause a fire anywhere in the passenger compartment. If in fact there was a fire in the passenger quarter panel area there are two things that would be the cause. Either wiring behind the kick panel became shorted and caused the fire or the exhaust became extremely overheated and caused the fire.

2007 Dodge Ram... | Answered on Jan 26, 2014

Not finding what you are looking for?
2007 Dodge Ram 3500 Quad Cab Laramie Logo

177 questions posted

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ram 3500 Dodge

  • Ram 3500 Dodge

Most Popular Question

cannot remove rear half front hub 2007

  • Cars & Trucks
Loading...