20 Most Recent 2007 Chevrolet Silverado 1500 2WD Questions & Answers

My thought was no shim kit fitted which makes the pads tilt, others may disagree and have other ideas. https://www.google.com/search?q=2007+Chevy+Duramax+Front+brake+locks+up+in+cold+weather ..

Take battery cable off for 5 mins, then put battery cable back on. Insert your key into the ignition turn to on but don't start the vehicle wait 5 seconds turn back off repeat the key on/off three times. This initiates a re calibration of climate control equipment and actuators. It will fix your problem.

Chevy dealer says will not come on until temperature reaches 219 f

Excessive Fix a flat in tire,,, bent rim,,, bent drive shaft,, or bad u joint,,

Vent solenoid is located by the fuel tank fill hose mounted to the box.

Yes it will cause the check engine light to come on if it is not tightened.

Replace pump up lifters,, or install Active fuel management delete kit,,best bet

I, feel sorry for you, after reading your problem, but don't worry you visit the Reliable-Store they will help you for sure. Best Manuals

It obviously has damaged speakers the sound you describe is the signals distorting through the damaged speakers they should replace as it's a service fault as much as any other faults and as such should be fixed I would demand they fix it especially if it is under warranty still

Even though you have a manual HVAC system it still has the capability to set an store DTC'S - diagnostic trouble code's . DTC B0413 02: Temperature Control 1 Feedback Circuit Short to Ground (CJ3) DTC B0413 05: Temperature Control 1 Feedback Circuit Short to Battery or Open (CJ3) DTC B0413 61: Temperature Control 1 Feedback Circuit Actuator Stuck Open (CJ3) DTC B0423 02: Temperature Control 2 Feedback Circuit Short to Ground (CJ3+C67) DTC B0423 05: Temperature Control 2 Feedback Circuit Short to Battery or Open (CJ3+C67) DTC B0423 61: Temperature Control 2 Circuit Actuator Stuck (CJ3+C67) Did you have Actuator Recalibration done after replacing the actuator or control module ? Your best bet ,take your vehicle to a qualified repair shop . Preferred Method (w/ Scan Tool) Clear all DTCs. Place the ignition switch in the OFF position. Install the HVAC actuator. Connect all previously disconnected components. Start the vehicle. With the scan tool, initiate the Motor Re-calibration feature of the Heating and Air Conditioning Special Functions menu. Verify that no DTCs have set as current DTCs.

Sounds like it might be a damaged rear end. Chock the wheels or put rear differential on jack stands and put vehicle in neutral then by hand turn the drive line back and forth and see if there is any loud noise when u do. There should not be a lot of play. if on jack stand you can also turn one of the rear wheels and see if there is any load noises or excessive play

go to the wreckers and get a replacement fuse holder and wiring harness quicker and easier than trying to replace the fuse holder of the damaged wires

Time for a rebuild

I had the same problem! I used a piece of wood to keep the break pedal depressed and then started to remove one of the break lamps and to my surprise it came on! Same thing on the other side. So I did not seat (bottom out) the lamps in their sockets and both break light are now working properly. I had a similar issue last spring but that time only one light was out. I put in a new bulb and it still did not work so I messed around with it a little more and it started working. Never did figure it out until now. Hope this helps!

Transaxle Control System Malfunction https://www.autocodes.com/p0700_chevrolet.html

Here you can look it up , may like to have this for future reference ! http://bbbind.com/free_tsb.html free wiring diagrams an fuse box diagrams as well . When you click on this blue link I copied , click on wiring diagrams , not TSB'S ! You may want to check them out later ! TSB'S are technical service bulletins .Well ant way ,after you click on wiring diagrams enter your vehicle info. , year , make , model , engine size . Then under system click on electrical distribution , under subsystem click on fuse panel .Then click search . Two blue links will show , click one at a time till you find what your looking for .

code p 0700 refers to transmission control system/MIL---malfunction==== causes --TCM---wiring check all connections and wiring condition or replace the TCM code p 0717 refers to turbine shaft speed (TSS) sensor ---no signal====causes ---wiring---TSS sensor---ECM/TCM logically the TSS reports to the TCM to facilitate ratio changes so if the wiring , connections etc are not good then one will affect the other Take it to an accredited auto transmission specialist shop, have it properly diagnosed and a quote do not confuse a TSS with a VSS sensor as they are two different speed sensors in the same box

Kingston Jamaica