Top 20
2008 Chevrolet Silverado 1500 2WD Questions & Answers
I have a serious problem with my chevy silverado
Which sensor? They are replaceable. Do not trust that dealership.either they don't know what they are talking about or they are a rip off. Drive it untill light comes back on and go to a auto parts store. They can pull the codes. Write them down and google the codes and watch some videos on how to do it yourself. Get the part you need and replace it yourself.
Why is the fuel pump fuse not getting any power feed?
The fuse gets it's power from the fuel pump relay , located in the under hood fuse/relay box. An the ECM- engine computer energize the relay . This does not mean the relay is bad ,Because you have no B+ at the fuse. The thing to do is test for B+ voltage at pins 30 an 86 while cranking the engine . The relay position will be given on the under side of the lid for fuse/relay box. Pull the relay an look at the bottom ,pins side or terminals ,what ever you would call them . Each terminal is marked with a number 30,87, 85 ,86 . The ECM will only energize the relay when it receives a message from the BCM - body control module , with no anti-theft system problems . Do you have a pad lock an car symbol lit on the instrument cluster ?
Why is there no power to the fuse box for the fuel pump fuse?
Takes an electrical diagram, volt meter, and a bit of time to figure out. Check other fuses that should have voltage with the key on. If there's no power to them, then it would be the ignition switch. If there is, then a broke wire would be the cause.
Turn signal location 2008 chev. silverdo
Not sure what you are asking here but the turn signal assembly where you move the arm to turn left or right is in the steering column. The power unit should be attached to the fuse panel it will be the large round alum. looking relay. Hope this helps.
How do i remove the back seat in my 2008 chevy 4 door truck
don't know this vehicle specifically but on many cars the rear seat base is held on with a clip on each side. Grab the seat at the front bottom, push back/down, then pull up. Same for other side. Once the base is out there is often a bolt on each side holding the seat back on. Take out the bolt and lift the seat back up.
Remove heater ac air posion moter on 2008 chev pickup
I think the part is called the blend door actuator.
1.You have to remove the plastic cover on passenger side. Motor is located over the transmission hump.
2. Remove wiring harness plug.
3. Remove 3 hex head screws.
You need a small 1/4 socket set.
2008silverado 4.3v6 has miss when you ecellrate changed plugs doing it again engine light back on
Since the engine light is back on the code is likely to help you diagnose the problem.
1. If you have a code reader for your car plug it in and it should tell you what the computer thinks the problem is.
Remember for the engine to miss it has to be loosing fuel or spark. The spark plugs are only one of the parts required to make a reliable spark in the plug as the engine is running.
2. Check the spark plug wires and the distributor internal for rust contamination around the reluctor magnet area. The 4.3 chevys are bad for this. Have someone start the car for you at night while you look under the hood for spark leakage. In the dark any wire leaking spark enough to make it miss on acceleration will flash blue lights in the dark.
3. Replace the fuel filter.
4. Check for vacuum leaks in the rubber tubing plugged in to the intake manifold.
5. Make sure the battery to engine ground cable is in good condition at both ends and tight.
6. Make sure the battery to chassis ground wire is connected clean and tight.
Good luck.
Unlock a 2008 Chevy Silverado
This year model truck WILL allow the truck to be locked if the key fob is left inside, but not while fully engaged in the ignition. If you do not have Onstar service you will have to use a long piece of thin metal, possibly a straightened clothes hanger and work it into the upper part of the driver or passenger side door at the top rear corner. Be careful not to tear the door seal. If it's long enough to reach the power door lock button press it to open the door. If not then fashion a small hook on the end and hook the manual door lock release. There is just enough of a lip to hook on to. Hope this helps.
How do I unlock my 2008 Chevy Silverado Truck?
Slim Jims won't work on the door. There is a tool called The BigEasy unlock tool. You sneak it between the jam and door frame and hook it on the lock knob and pull it to unlock the door or push the power lock button to unlock the door.
Not finding what you are looking for?