Top 20 2007 Lincoln Aviator - Page 6 Questions & Answers

Heated Cooled Seat Control Module . B2486- climate control seat module voltage out of range. Did you test voltage out of range with DVOM - digital volt ohmmeter ? B2486 Climate Control Seat Module Voltage Out of Range On-Demand and Continuous REFER to Section 414-00 to diagnose the charging system concern. B103C Thermoelectric Driver Open Load On-Demand and Continuous Go To Pinpoint Test T . Pinpoint Test T: DTC B103C - Thermoelectric Driver Open Load Refer to Wiring Diagrams Cell 119 , Climate Controlled Seats for schematic and connector information. Normal Operation Both the driver and front passenger climate controlled seats are independently controlled electronically by the dual climate controlled seat module (DCSM) mounted to the bottom of the passenger seat cushion. The climate controlled seat system only operates with the engine running, however, if using a scan tool to command the DCSM, diagnostic testing can be carried out with the ignition switch key ON engine OFF (KOEO). The system receives power from battery junction box (BJB) fuse 12 (30A) feeding battery voltage on circuit SBB12 (GN/RD) into DCSM C3305a pin F. The system also receives power from BJB fuse 11 (30A) feeding battery voltage on circuit SBB11 (BU/RD) into DCSM C3305a pin E. If power is disconnected from either pin E or F of DCSM C3305a with the power connection remaining on the other circuit, both seats will remain operational because the power feed circuits are connected internally in the DCSM. However, if a fault occurs setting a DTC specific to either climate controlled seat, only the affected seat will be disabled by the module and the other will remain operational. Each driver and front passenger seat cushion is equipped with a thermo-electric device (TED) assembly that includes a seat blower (fan motor, serviced as an assembly with the TED). Similarly, each driver and front passenger seat backrest is also equipped with its own TED assembly with blower. Cabin air is drawn through the blower and distributed to each of the TED modules located in the seat cushion and backrest. The TEDs then heat or cool the air. The air is then directed into the foam pad and manifold where it is distributed along the surface of the cushion and backrest of the seat. Once the system is activated, the DCSM uses a set of flexible algorithms to control the heating/cooling modes and the blower speed dependant on the EATC seat switch settings. Possible Causes A TED driver open load fault can be caused by:

• wiring, terminals or connectors.
• a faulted TED assembly.
• a faulted DCSM.

Gary, check here.... https://www.carcarekiosk.com/video/2012_Lincoln_MKT_3.7L_V6/lights/center_brake_light

Ck the posts here.... https://lincolnforums.com/forums/threads/continental-battery-drain-check.37502/

ck here... https://www.google.com/search?q=Ac+lines+for+a+2000+LS+Lincoln+v6+3.0&newwindow=1&sxsrf=APwXEddCg0HQF91r0kdw2e9V2PhDp_RLww%3A1685805148348&source=hp&ei=XFh7ZNGcEsHn0PEPhoSf4AQ&iflsig=AOEireoAAAAAZHtmbGoPc0j-xflXXsV3HXjuOrOuG1V0&ved=0ahUKEwjRupnIsaf_AhXBMzQIHQbCB0wQ4dUDCAo&uact=5&oq=Ac+lines+for+a+2000+LS+Lincoln+v6+3.0&gs_lcp=Cgdnd3Mtd2l6EAMyBQgAEKIEMgUIABCiBDIFCAAQogRQAFgAYPApaABwAHgAgAHEA4gBxAOSAQM0LTGYAQCgAQKgAQE&sclient=gws-wiz

https://www.cargurus.com/Cars/Discussion-t7468_ds782699

It's between the gas tank and the engine. Google the filter and you might be able to recognize it. The AutoZone part number is FF610DL approximately $3.89. Hope this helps.

no problem told to help any WILD BLIND HUNTs gee and engine can have 3 temp sensor for coolant and 1 for air and 1 inside the transmission(not 1969) back then, no computers (a joy) one is just for dash coolant meter. one for AC overheat. no engine told ahh is 460 cu in (7.5 L) V8 (385 family) on most that old the sensor on the engine, near coolant path has only 1 wire. brass color, and tiny threaded terminal x1 not 1 wire sensor on side of block, for oil the huge clue is 1 wire. sensor and the oil see rear top of engine ,?

Some vehicles need to be reset after a fail safe issue has been repaired. This is commonly done using an OBD diagnostic tool. If you have to pay for this ask at 4 or 5 different places as prices can be VERY different.

this 5.4L USA spec car/engine, 1 of ...

The P07** relate to transmission issues, the rest fuel/air mixture. From what you have done so far, I recomend you take it to a garage for professional service. If you replaced the O2 sensors with aftermarket ones, that is the first thing I would suspect.

https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&cad=rja&uact=8&ved=2ahUKEwiUjPSB8_L-AhWMATQIHV2aCxUQwqsBegQIDxAF&url=https%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3D_YIIyc5l4xQ&usg=AOvVaw1IvZvDQasXzj9Q3R2GsfVj

check fuses and relays --check inertia switch --test fuel pump and circuit

no engine told or country . 2.4diesel turbo or the 5.;0l gas back to the future posts. 39 years old. TBI INJECTED GAS? SM QUOTE .GAS A single internally gas tank mounted pump is used on fuel injected models through 1983 and on 1984 and later Lincoln Town Car. Other 1984 and later models equipped with a high output injected engine are equipped with two electric pumps. A low-pressure pump is mounted in the tank and a high pressure pump is externally mounted. IF CAR WAS MADE NEAR JULY IT MIGHT BE SETUP WITH DUAL PUMPS. ONLY LOOKING FIRST ANSWERS THIS RIDDLE.

It is caused by from having a bad fuse and the fuse will need to be replaced in your car.

Question edited for clarity and toss in some upper CASE letters. There are all in one place under the centre of the dash. https://www.google.com/search?q=2013+Lincoln+MKS.+Mode+control+actuator+location

search yuotube " LINCOLN MKX FRONT BUMPER COVER REMOVAL REPLACEMENT "

If the front blinkers on your 2011 Lincoln Navigator are not working, but the rear blinkers are, there are a few things you can check:

1. Check the fuses: The first thing to check is the fuses for the turn signals. Look for the fuse box that contains the fuses for the turn signals and check to see if any of them are blown.
2. Check the bulbs: You mentioned that you already checked the bulbs, but it's always a good idea to double-check. Make sure the bulbs are the correct size and are securely installed.
3. Check the wiring: Check the wiring for any visible damage, corrosion or loose connections. Look for any frayed or damaged wires that may be causing a short circuit.
4. Check the turn signal switch: The turn signal switch may be faulty, preventing the front blinkers from working. Test the turn signal switch to see if it is working properly.

If none of these steps solve the problem, it's possible that there may be an issue with the wiring harness or the control module. In this case, it's recommended to take the vehicle to a professional mechanic for further diagnosis and repair.

notify dealer need vin and proof of ownership