Top 20 2006 Mitsubishi Outlander Questions & Answers


If the cause of the problem is fixed, the light will go out by itself. If you haven't fixed the underlying problem, the light will stay on. You can clear the codes with a scan tool, but it'll come right back on the instant you turn the ign key.

2006 Mitsubishi... | 29 views | 0 helpful votes


Why did you replace the sensor in the first place is the first question. If it already didn't start then the crank sensor was not the problem, crank sensor faults can be logged for other reasons. If it did start put the old one back in and try again.

2006 Mitsubishi... | 64 views | 0 helpful votes


You need to contact the dealer for this problem there is nothing you can service to fix this.

2006 Mitsubishi... | 50 views | 0 helpful votes


1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.
Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select (language cooperative control).

3. Press and hold the multi-information meter switch to switch in sequence from

3. Press and hold the multi-information meter switch to switch in sequence from A or 1 (language cooperation enabled) ? M, 2 or P (language cooperation disabled) ? A or 1 (language cooperation enabled).

Hope you get your problem fixed :)

2006 Mitsubishi... | 2,231 views | 0 helpful votes


Sending unit is bad its float thats in the tank reads to the gauge very rare that it will be the cluster its self could even be a ground in some cases

2006 Mitsubishi... | 853 views | 0 helpful votes


Go to your dealer and ask if the motors have the same part number if so they are inter changeable , In most states the windows must function to be road worthy .

2006 Mitsubishi... | 74 views | 0 helpful votes


that's not a big issue u can repair it your self with the help of service/repair manuals 2006 Mitsubishi Outlander buy from the link
and get it done

2006 Mitsubishi... | 69 views | 0 helpful votes


oil pumps are in the sump and run in oil
there is no bearing as such as the shaft and gears are just a close fit in the cast housing which is lubricated by passing oil under pressure
as for a noise, if you can hear it there will be little or no oil pressure
However water pumps bearings regularly fail and you will hear it. mostly a sort of tinny rattling noise or a low grumble.

2006 Mitsubishi... | 65 views | 0 helpful votes


Fault code p2138 if you know it? If you don't. Google it.

2006 Mitsubishi... | 275 views | 1 helpful votes


you need to lift up the black plastic covers with a screwdriver or another flat tool at the front bottom side and split the one in the middle on the top - slide them away -then you should see the screws holding the rack to the rail.
25405094-l2syhiveb5h5n2hnqsepdito-4-0_1.jpg

25405094-l2syhiveb5h5n2hnqsepdito-4-2_0.jpg
25405094-l2syhiveb5h5n2hnqsepdito-4-20.jpg split one side and lift the bar away to see screws

25405094-l2syhiveb5h5n2hnqsepdito-4-27.jpg

2006 Mitsubishi... | 562 views | 2 helpful votes


Becker Radio Code
If the display shows CODE WAIT then the car radio is probably blocked by too many incorrect entries. You can re-enter the code after leaving the device simply up to 3 hours with ignition ON !
- BUT:
if you DON'T know the code then you need to pay for a decoding service on eBay....
(I do hope you are the legal owner of the radio)
25318604-l2syhiveb5h5n2hnqsepdito-3-0.jpg
25318604-l2syhiveb5h5n2hnqsepdito-3-9.jpg
BECKER AM FM RADIO CD STEREO DECODE CODE KEY UNLOCK SERVICE

2006 Mitsubishi... | 1,567 views | 1 helpful votes


Hi, did you know there is a recall on the indicator/headlight stalk. The plug in the base may be faulty. I wolud check with a Mitsubishi dealer or gGoogle, if your car is included. You need your VIN number. Does it work when you pit your hazards on or you lock the car? If not may be it is the plug in the back of the globe. Good Luck

2006 Mitsubishi... | 89 views | 0 helpful votes


The code is printed in the Owners Manual, IF you bought it without the owners manual you need to take it to a dealer to look up the code.

2006 Mitsubishi... | 174 views | 1 helpful votes


You may have a security issue with your key not being recognized by your vehicle, or possibly a weak fuel pump. It would be best to have it diagnosed at a shop.

2006 Mitsubishi... | 124 views | 0 helpful votes


Not meaning to be smart but has it any fuel? or possibly fuel pump not working is it turning over ?perhaps battery fault.

2006 Mitsubishi... | 35 views | 0 helpful votes


drive to the dealer and ask that.....
only they know what is there, (unstated) and can help.
cars have many audio options day 1.
and many are upgraded later,

2006 Mitsubishi... | 41 views | 0 helpful votes


this mite be a inlet valve problem

2006 Mitsubishi... | 846 views | 0 helpful votes


check for worn loose "u" joints . check for loose drive shaft pinion. Check for worn suspension rubbers on rear end allowing the arms to move up and down

2006 Mitsubishi... | 233 views | 0 helpful votes


May simply be the throttle body adjustment. This is all dismantled to get to the head gasket.

2006 Mitsubishi... | 148 views | 0 helpful votes

Not finding what you are looking for?
2006 Mitsubishi Outlander Logo

181 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Outlander Mitsubishi

  • Outlander Mitsubishi

Most Popular Question

vehicle cutting out

  • Cars & Trucks
Loading...