Top 20
2006 Mitsubishi Outlander - Page 6 Questions & Answers
Mechanical
Surely you know when you get any check lightson your dash, you have to check for codesIt has been over 30 years we have had that
8/10/2013 10:51:40 PM •
Mitsubishi...
•
55 views • 0 helpful votes
Mi suv outlander 2012 me da un codigo p0300 que puedo hacer?
Hello
The
Engine and Automatic Transmission (not applicable to manual
transmissions) in this vehicles drive train are fully electronically
controlled by a computer called the PCM and TCM (Power Train Control
Module, Transmission Control Module). When a problem like this or
other drive-ability related problems occurs the computer stores a
record of the problem (there are of course some exceptions to this,
like the fuel pump, engine coolant temperature sensor and MAF sensor
for instance) in the form of a fault code in its memory, to read
these fault codes you must have the systems memory scanned with a
special tool. Once the fault code(s) are read you then must perform
the appropriate diagnostic testing to find and resolve the
problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED
TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPENDING YOUR HARD
EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM. Also always
check fuel pressure for correct spec for your make and engine type.
9/27/2012 11:15:31 AM •
Mitsubishi...
•
217 views • 0 helpful votes
Why is the slap stick on my suv not working
I have an '04 Outlander and the manual slap stick stopped working. I also noticed the Drive light was not on when in auto drive. This is a common problem with this model and a relatively easy fix. Tools you will need are a small flat head and medium cross head scredriver, solder gun and electronic grade solder, small heat shrink tubing. Remove the entire center console - start at the rear by removing the 4 philips screws in the center arm rest compartment, remove the cover plate underneath the hand brake and the 2 side panels on either side at the front. Remove the shift knob (2 screws behind the small cover plate on the front of the knob - remove with small flat head screwdriver). Remove all remaining screws and the rear section, then slide the center section over the handbrake followed by the front section.
You will see a small switch on the shift lever with 3 wires (Black, Blue and Red). Most likely one or more have become detached, at this point it is best to unsolder any that are still attached because they will likely break in the near future! Remove any old solder and wire from the 3 contacts with the solder gun on the switch and tin each with fresh solder. Strip about 1/8" on each of the 3 wires and tin each with solder. Slide about 1/2-3/4" of the heat shrink tubing onto each wire. Solder the wires back to the swtich in this order:
Black - top
Blue - center
Red - bottom
Start at the top and work down, and after soldering each slide the heat shrink tubing over the solder joint and shrink by applying the solder gun - this will provide better mechanical support and help prevent future breakage.
Reassemble the center console in the reverse order of removal - make sure you have no screws left over!!
Good luck - hope this helps.
10/7/2012 6:44:53 PM •
Mitsubishi...
•
133 views • 0 helpful votes
Can't get the SRS light to go off?
SRS means Supplementary Restraint System or as an Air Cushion Restraint System (ACRS), if the light is on, it is most likely a computer response telling you something is wrong. The SRS refers to the deployment of your airbag in an accident.
7/22/2012 6:25:30 PM •
Mitsubishi...
•
964 views • 7 helpful votes
Airtrek srs light on
"SRS" stands for: "Supplemental Restraint System". The primary restraint system are the seat belts / shoulder belts. The SRS consists of the air bags that are located in the steering wheel and dashboard that help protect the driver and front passenger(s) in the event of a collision. Additional airbags (often located in the side pillars between front and rear doors) help protect from side impacts may also be present - depending the year and model vehicle you have. An SRS light that remains on in the instrument cluster indicates that a problem has been detected by the on board computer. It normally should not interfere with the operation of the vehicle, but some or all of the SRS components may not work when needed or may activate unexpectedly - depending the type of problem with the SRS.Many states that require vehicle safety inspection at regular intervals may fail a vehicle with an SRS issue. Be aware that these systems may be costly to repair. The auto dealer and most modern repair garages have the technology to obtain the SRS problem data that is stored in the on board computer, and should be able to provide you with more information about the nature of the problem and approximate cost of repair.I hope this helps & good luck!
4/26/2012 9:51:22 AM •
Mitsubishi...
•
496 views • 0 helpful votes
The fuel door on my
There should be a manual pull probably inside the trunk at or near the area of the fuel door.
If you have a manual, the location would be shown in it.
Gary
8/7/2011 10:16:08 PM •
Mitsubishi...
•
1,507 views • 0 helpful votes
Hi i have a
is the heater plug jumper rail earthing out ? dissconect the live feed off the heater pulgs and see if that helps.
9/21/2011 9:09:58 AM •
Mitsubishi...
•
148 views • 0 helpful votes
Workshop manual book for Mitsubishi
I have some workshop and service factory service manuals but they are geared more towards the model not just Mitsubishi so I would need to know what you are looking for and then i would need to figure on how to email them to you. They are pretty big files on some of them. You can get a hold of me at
[email protected] and I will see what I can do.
6/28/2011 5:34:08 PM •
Mitsubishi...
•
781 views • 1 helpful votes
Not finding what you are looking for?