2006 Mitsubishi Outlander - Page 7 - Answered Questions & Fixed issues

In the body shop that was just about what we would have to do when there are no visible screws and it was the first time removing a panel in a new type of vehicle.

Those panels are usually held in place with some metal clips (sometimes plastic molded into the panel) that snap into slots in the body. You can lightly pull and get a feel for where there is reistance. Slide a thin tool like a paint stick (or something stronger) and use it to pry up in the area of resistance. You may also be able to pry up and look under it to see where the clips are.

Mitsubishi... | Answered on Sep 03, 2011 | 51 views

  • Hi, I can help.

  • Open the door and look on the inside of the door where the mirror mounts from the outside. Often times Mitsubishi's mirror access panel is behind a corner of the door panel and it is just a little corner piece that pops off.
  • Follow these steps ---
  1. You will either see some screws right away or a little panel that will have a screw to remove (some of then you just gently pry off with a flat tool. If no screws the gently pry off.)
  2. Now you will see a wire harness that is coming down from the mirror. Gently lift it up until the connect is reached.
  3. Remove the connector and don't let it drop down. Anchor with a little duck tape.
  4. Now you will see three nuts that need to be removed ( I think 13mm ).
  5. Make sure you support the mirror as you are removing the last bolt.
  6. Now wiggle and jiggle the mirror out and pay attention so the harness comes out freely with it.
  7. It's a basic reversal to install the new mirror.

  • If you have any comments please feel free to leave them here and I will respond to you.
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Mitsubishi... | Answered on Sep 02, 2011 | 77 views

check the flasher unit. most auto part stores will assist you

Mitsubishi... | Answered on Aug 14, 2011 | 114 views

Are you going by the gauge that says fuel economy on the dash, if so try to zero out the gauge or reset it ,this will recalculate the reading.

Mitsubishi... | Answered on Aug 11, 2011 | 168 views

There should be a manual pull probably inside the trunk at or near the area of the fuel door.
If you have a manual, the location would be shown in it.

Mitsubishi... | Answered on Aug 07, 2011 | 1,202 views

maybe dead rat in air vent or air intake,fan,etc.

Mitsubishi... | Answered on Aug 07, 2011 | 194 views

Its a good idea to change plugs every 50K miles...so go ahead.
By looking at the plugs you can check engine's health.

With no codes...I'd suspect a fuel leak somewhere...

Hope this helps...

Mitsubishi... | Answered on Jul 30, 2011 | 124 views

Here is the Module...

Below is the relay...Hope this helps??.michael_cass_238.jpg

Mitsubishi... | Answered on Jul 03, 2011 | 1,494 views

I have some workshop and service factory service manuals but they are geared more towards the model not just Mitsubishi so I would need to know what you are looking for and then i would need to figure on how to email them to you. They are pretty big files on some of them. You can get a hold of me at csautomotivecars@att.net and I will see what I can do.

Mitsubishi... | Answered on Jun 28, 2011 | 760 views

If you have unexplained current draw, the best way to troubleshoot is with an accurate clamp on amp meter. Then you pull the fuses - all of them - and then put one fuse in at a time and write down what the reading is. When you find the item that is drawing far more current than what it should then you have a starting point.

It is a long drawn out operation and takes an accurate fuse box diagram with fuse sizes, but it does allow you to pin down unexplained current draw problems.

Mitsubishi... | Answered on Jun 28, 2011 | 162 views

This all depends on the year and the rtype of sparkplug being used, for example a regular sparkplug i would replace at about 40,000 miles but then you have paltinum and double platinum sparkplugs that i have seen go 100,000 miles but i would replace those at about 70-80,000 miles. good day.

Mitsubishi... | Answered on Jun 19, 2011 | 126 views

Mitsubishi doesn't provide warranty to gear box,motor and plastic fittings etc!!

Mitsubishi... | Answered on Jun 13, 2011 | 44 views

Most manuals can be had online after a bit of a Google search....
a 2011 may be a bit hard to find though...

Mitsubishi... | Answered on Jun 09, 2011 | 117 views

Hi :) There is a tab of steel on a brake pad that sqeals when the pad is getting low on thickness to let you Know it is time to change the brake pads and only sqeals at low speeds Have the brake checked out by a Mechanic.This tab is only on disc brakes not drums.

Mitsubishi... | Answered on Jun 06, 2011 | 300 views

Did you ever sort this ? I've a similar overheating issue and just wondered ? Thanks ...

Mitsubishi... | Answered on May 30, 2011 | 478 views

Hello maothilak: My name is Roger and I will help you. According to my repair manuals and shop guide . The timing belt should be replaced every 96560.82km. or every 60,000 miles. Please note this engine has been identified as an interference engine. That means if the belt slips or breaks severe internal damage will occur. With the mileage you have on your engine I would recommend changing the timing belt. You did not say which engine you have? My all data system identified it as a 2.4 sohc engine. Should you have a 3.0 engine than the time to change the belt is 168981.4 km or 105,000 miles. The 3.0 is also considered an interference engine. Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Mitsubishi... | Answered on May 25, 2011 | 225 views

Not finding what you are looking for?
2006 Mitsubishi Outlander Logo

181 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides