2006 Mitsubishi Outlander - Page 9 - Answered Questions & Fixed issues

Thats because the software is encrypted to prevent home mechanics ,take it to a dealer

Mitsubishi... | Answered on Jan 03, 2011 | 130 views

This part is only replaced if it fails or is noisy, there is no regular replacement required.

Mitsubishi... | Answered on Dec 30, 2010 | 47 views

is it the switch or is it the mechanism ,the one inside the door

Mitsubishi... | Answered on Dec 29, 2010 | 106 views


Mitsubishi... | Answered on Dec 18, 2010 | 13 views

auto trans are complex and cud be a # of things-specialy with age and milage--however a shift solenoid may be failin or a relay--also a clutch may be smoked or a problem in the valve body--have u had a drain and fill service--have vehicle scanned for bad codes

Mitsubishi... | Answered on Dec 07, 2010 | 181 views

On the relay box look for the Acc. Socket fuses #23 -10A and #25 - 15A. To fix the socket, remove the Center Lower Panel using a flat tool or a butter knive to make the clips on each corner pop out, the socket can be re-tightened, they usually do not get damaged. once fixed, snap the Center Lower Panel back into the dashboard.
Check the following diagram.

If you need better quality images, please provide an email address to send them to.
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Mitsubishi... | Answered on Dec 06, 2010 | 407 views

this code refers to the throttle position sensor. most likely it is a faulty tps sensor. i have replaced a few of these on mitsubishi,s the code refers to low voltage input meaning the computer is seeing to low a signal from the sensor. to replace look on opposite side of throttle shaft from where throttle cable is hooked up will be a sensor held on by two screws.

Mitsubishi... | Answered on Nov 22, 2010 | 226 views

we need to replace the gasket

Mitsubishi... | Answered on Oct 31, 2010 | 165 views

The play in the turbo is why you have the leak with out rebuild shop tools all you can do is change the turbo (if a lot of oil gets into inlet
system engine can run away and will not stop ((English mechanics
call this drinking its own blood)))

Mitsubishi... | Answered on Oct 24, 2010 | 436 views

P0340 Camshaft Position Sensor Circuit Malfunction
P0335 Crankshaft Position Sensor A Circuit Malfunction\

Based on the codes you listed I would have to say it appears the Crank Position sensor is either malfunctioning or you accidentally caught the wires between two parts that were bolted together and they shorted out. Double check the Crank Position sensor wiring and make sure you have them connected correctly and don't have a short on any of the wires.

Mitsubishi... | Answered on Oct 15, 2010 | 154 views

You more than likely have air in the system.Grab another person if you know how to bleed the slave cyl,but only for a hydraulic clutch.If it is a cable clutch,adjust the cable.

Mitsubishi... | Answered on Oct 02, 2010 | 64 views

take it nto a trans shop & have a service/ band adjustment done...

Mitsubishi... | Answered on Oct 02, 2010 | 406 views

Possible that the dashboard cluster ground is faulty and the reason why all the lights of the dash are on. the dash is normally triggered bythe park lamp switch and so ther must the + 12 coming tothe lamps on switch on.

Mitsubishi... | Answered on Sep 25, 2010 | 244 views

Please see my tip at http://www.fixya.com/cars/r5932051-check_engine_light_check and let me know if you have questions.

Mitsubishi... | Answered on Sep 24, 2010 | 54 views

Try getting some additives to clean your lifters...i think they are called lifter free..a nulon product ..change oil and filter and then try it or get new lifters installed and adjusted.Blocked lifters will make a sound like that and it's pretty common with mitshubishi.Also check if your idler bearings are ok.

Mitsubishi... | Answered on Sep 21, 2010 | 456 views

Your problem is probably something pretty basic (like an oxygen sensor). If you go to the local auto store they will usually plug into your car with a code reader and tell you what you need to replace . At that time they can also turn off the service engine check light (if something is wrong chances are it will come right back on). Auto stores will diagnose your car for free to get you to buy the repair parts to fix your car from them. So go to your go to the auto store and let the car tell you what it needs and show your patronage by getting your parts there.

Mitsubishi... | Answered on Sep 03, 2010 | 171 views

This is a interference engine and you probably have engine damage.

What i do in a situation like this, is i replace the timing belt and do a compression test, i have been lucky on more than one account .

Other wise be prepared for bent valves and dented piston heads

Kind regards Indy .

Mitsubishi... | Answered on Aug 17, 2010 | 198 views

Good Evening, that is a relatively good question which not many people would think to ask. What that will do over time, rather quickly than not is wear the last rib off of the belt wearing it out a little faster starting on the area the rib was run off of. Other than that it will simply ride in the 4 ribs on the replaced pulley and the 4 ribs of the other pulleys. Hope this shed some light for you and helped.

Mitsubishi... | Answered on Aug 12, 2010 | 68 views

How to reset computer after oil change on 2008 outlander

Mitsubishi... | Answered on Jun 17, 2010 | 1,029 views

there will always be a certain amount of metal in a gearbox(hopefully on the bottom out of the way)drain and refill with new oil.as long as its not whining or some other noise that sounds expensive you should not worry.

Mitsubishi... | Answered on Jun 09, 2010 | 96 views

Not finding what you are looking for?
2006 Mitsubishi Outlander Logo

181 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides