Top 20
2000 Oldsmobile Intrigue Questions & Answers
Dashboard Lights
All are controlled by the ECM computer. I would suspect a bad ground. But wiring could be the culprit also along with the big connector in back of the dashboard. Poke around.
My daughters 2000 olds intrigue has a blown 40a
You should check out
www.reliable-store.com they have info on repair, service, wiring
diagram, electrical diagram, fuse diagram, troubleshooting, PCV, owner's/service/repair/parts manual, fault codes, error codes, etc everything on all vehicles. must check it out
How to replace hoses on 2000 Olds Intrique
Use channel locks to pinch the fastner then pull the hose off if it doesn't move push the clamp off the hose if still doesn't move then try using the wrench to twist it back and forth then it should come off. Then put new one on and refasten the clamp. U may have tolubeit to get into may want to switch the clamp to new ones
How to remove passenger side door panel, for 2000 Olds Intrigue?
1. Remove the door latch trim plate (coupe and sedan front doors).
2. Remove the ashtray (sedan rear doors).
3. Remove the seat belt retractor cover (coupe and sedan front doors). Use a suitable door trim panel removal tool to release the clip retainers
4. Remove the door lock trim plate and the power window switch, if so equipped.
5. Remove the window regulator handle by removing the inner retaining clip, if so equipped.
6. Remove the remote mirror control, if so equipped
7. Remove the trim panel retaining screws
8. Remove the door trim panel using a door trim panel removing to work loose the retainer clips.
9. Detach all electrical and remote mirror controls, as required.
To install:
10. Install the wiring harnesses through the openings in the panel, as equipped.
11. Position the trim panel to the door and align the clips. Press the trim panel to the door until all the clips are fully engaged. Align all the holes before engaging the clips.
12. Install the screws, remote mirror control and inside door handle bezel, as equipped.
13. Install the window regulator handle or power window switch.
14. Install the door trim plate, seat belt retractor cover or ashtray.
My car is getting hot in idle, what is wrong?
Check first your coolant level. Start engine and turn on ac open hood see if cooling fans are running, if fans are running and coolant level is ok temperature should stay normal. If temperature rises squeeze coolant hose, it should be firm like you could feel pressure on the hose a sign that the water pump is good. Thermostat opens only when coolant reach normal operating temperature.
2001 intrigue not starting
If starter is clicking but not turning, usually an electrical problem or faulty solenoid. If nothing happens but lights dim, starter may be jamming.
If no other electrical problems with the car (such as an intermittent battery failure), check the electrical connection at the solenoid for looseness or corrosion. If there is full 12V power at the starter solenoid and it still won't start, replace the starting motor.
Replaced blower motor, now runs continuously.
Run's continuously ? High speed , low , med 1,2, 3 . ????
Probably the high speed relay contact's stuck closed . The fuse for the high blower is hot at all times , low blower fuse is hot only with key on. It sparks becaused the motor turns on . If it had a short the fuse would blow . The blower motor relay is part of the resistor pack near the blower motor .
2000 Intrigue won't start, no
Sounds like there is a bad fuse somewhere. Not a pcm problem, but could be bcm. Check ignition and bcm fuses with ohmmeter.
Interior Lights, Radio, and Gear Indicator Light on Cluster will not turn off when power is connected
The door actuator ,door ajar switch has nothing to do with the
Gear Indicator Light on Cluster .
Did you have the BCM programmed ? Can't just replace this without programming . Having the BCM check for DTC'S - diagnostic trouble codes should have been the first step in the diagnostic's for this problem an testing power an grounds . Is the door ajar light lit on the insturment cluster ? If not ,it's not a door actuator or door ajar switch .
Important: Perform new BCM setup when you replace Body Control Module (BCM). Refer to Body Control Module (BCM) Programming/RPO Configuration .
Fuse Block
Right side of the IP, in the right front door opening
RAP relay ,contacts stuck closed . Right I/P fuse box ! Open the passenger door ,at the end of insturment panel pull plastic cover !
2000 olds intrigue - while
Fuel filter...maybe. More likely a cam position sensor or throttle position sensor. Have a code reader check for codes to pinpoint the problem.
Not finding what you are looking for?