2006 Dodge Charger - Answered Questions & Fixed issues

Question edited for clarity. Question moved to model category. When it overheats, check the radiator fan is running, but the most likely reason is that all of the air wasn't bled out. It has to be done a certain way. https://www.fixya.com/cars/r29872074-vehicle_cooling_system_no_heat ..

no info generic answer have vehicle scanned for trouble code[s]

Check this website https://www.autogenius.info/dodge-charger-2005-2010-fuse-box-diagram/

Tail light fuse is under the hood in the TIPM. The tail lights are controlled by the Body Control Module... Make sure you haven't lost the common (ground) before replacing any parts.

Question edited for clarity. Question moved to model category. Yyou can't diagnose issues like this yourself. You need more that a $125 scan tool. You need an auto electrician with a $5,000 bi-directional scan tool computer and the experience to use it. This is all electronics and computer networks and can't be guessed. P2127 Dodge The P2127 code means that the throttle or pedal position sensor switch E has a low input. The pedal position sensor is a sensor found on the gas pedal. The sensor tells the ECU when the gas pedal is depressed and how far it is depressed.

P2127 OBD-II Trouble Code: Throttle/Pedal Position Sensor ...

your timing may be off usually when that happens . . have u done any work to the car recently?

Question edited for clarity. Question moved to model category. Those two lumps just by the tyres. https://www.chargerforums.com/cdn-cgi/image/format=auto,onerror=redirect,width=1920,height=1920,fit=scale-down/http://www.chargerforums.com/forums/attachment.php?attachmentid=190897&stc=1&d=1439610224 Full System here https://www.carid.com/2006-dodge-charger-exhaust-parts/walker-intermediate-pipe-18154853.html ..

This is not an error code. It pinpoints that other error codes might require your attention as it is an OCM (Occupant Classification-ECU) DTC present. The chances that the error is due to an uncalibrated seat. Get it read by a scanner, or take it to a dealer or car mechanic to reset.

Check fuses first then bypass the brake pedal switch with a paper clip or its your shift lock solenoid under the shifter.

Full overhaul or just pan drop?

depending on the engine size you will need to go to web site charger forums.com there it will show you a diagram of your engine and location ot the temp sensor

You need a dealer to scan the system and determine the cause, more than likely a defective door switch sensor.

My 07 dodge charger brake light,abs, esp, bas light on an check engine light on an the hand show u how fast u going don’t work I took it to auto zone an they run a check on it an the code showed up u1120 an u1121i replace the rear brake sensors an drove it around the corner but the lights are still on.

Have an 08 Charger that had a similar issue (0121, 0480, 1110, 1120, 0121 again), no speedometer, only thing that worked was tachometer. Had all new wiring done while trying to trace the issue-garage couldn’t figure it out. After talking to an online forum, replaced the TIPM relay fuse box (used off eBay for @$100). Solved the problem. And you can do it yourself if you’re even basically mechanical-it’s 5-6 large plug in connectors that can’t fit but one way. You just need a wrench and a screwdriver.

With rwd, the sensors appear to be on driver side of tranny. Any applicable trouble codes? If so, what was the code?

Hi, on my 06 Charger Hemi R/T , the airbag lights stay on. I was informed by Dodge that all airbags are RECALLED.
So, maybe check on that. I hope i helped.
Ginger

Don't mean to sound smart a$$ are anything look in the owners manual it is listed there all fluid capacities are listed .

There's this website www.reliable-store.com They have books on ALL vehicles. it covers wiring diagrams, electrical diagrams, fuse diagram, torque specs, PCV, error codes, fault codes, service info, repair info, parts info, troubleshooting owner's/service/repair/parts/maintenance manuals etc everything totally.. I have 1987 toyota 4runner model and I keep servicing and when needed repair it on my own. worth it !!!

Either the socket is damaged or ground wire not attached. Trace wires to where one is attached to frame or body.

Or could be lifters ticking. Try using a heavier oil and see if that helps.