20 Most Recent
1997 Mercedes-Benz C-Class - Page 7 Questions & Answers
I have remove the Gearbox
Hi,
Check again the shifting lever selector connection, you made a mistake in putting it back.
Tell us afterwards after you reconnect the shifter link again.
Hope that helps you!
8/8/2011 11:55:05 AM •
1997...
•
Answered
on Aug 08, 2011
Lighter not working ,no juice
Replace fuse or check lighter filament. These are the two most common areas that fail on the lighter. Fuse is under the hood, drivers side, by the windshield. Filament is the piece inside the lighter. These generally screw out and can be replaced at most auto parts stores.
7/30/2011 5:53:14 PM •
1997...
•
Answered
on Jul 30, 2011
Can i change out from
no you cannot its a chipped key ask a local automotive locksmith to programme a spare key for you
7/18/2011 8:28:01 PM •
1997...
•
Answered
on Jul 18, 2011
How to refill a/c on a 1997 mercedes E430
hello,good day,your low pressure connection is near your compressor and your high press.connection is located at your condenser (beside your ax.fan) right side ,standing in front,ty
6/6/2011 2:58:35 PM •
1997...
•
Answered
on Jun 06, 2011
The speedometer light not on.
can you please tell me how you got to replace the bulb and how did you get at it how did you get the clocks out of the dash
5/11/2011 6:57:20 AM •
1997...
•
Answered
on May 11, 2011
Auto transmisiion jamming. Error code
when you say 'jamming',do you mean stuck in a gear?When they lodge a fault or numerous faults,the system goes in to 'limp home mode'.It stays in one gear,a sort of a get you home but I now I've got your attention,get me fixed mode.
I cant find a code 90,even the conversion to P codes doesn't define this.It may be a manufacturer specific code,
on engine it is 90 -camshaft timing adjust actuator open cicuit or short to ground.
or 090-not used.
on trans conversions,009xx-P09xx-not used.
I suspect that my update for the codes needed hasn't been supplied to me.
I shall do some more research for you if needed.
4/2/2011 9:08:45 AM •
1997...
•
Answered
on Apr 02, 2011
I have a 97 c280
the contacts are dirty first try can of compresed air like you use on your pc,you might have to remove the switch and clean the contacts with rubbing alcohol.
4/1/2011 10:44:39 AM •
1997...
•
Answered
on Apr 01, 2011
Hello I have a 2002
you can get uncut chipped keys from ekeylessremotes.com for around $16 to program them yourself however you will need 2 working keys if not you will have to have a dealer or a locksmith program the key for you.
3/29/2011 12:38:41 AM •
1997...
•
Answered
on Mar 29, 2011
1997 MB C280 ABS light -replaced stop
quite easy to sort out but it will take a while with a lot of patience ,jack each wheel up in turn and remove then inspect the set up and determine what type of system you have ,now a 97 most likely uses a toothed ring with a sensor so first of all ensure toothed ring isnt loose on the drive shaft ,then follow sensor wires back from wheel to find the multiplug ,disconnect multiplug and then use a automotive meter set on millivolts lowest setting and then spin shaft and see if you get a reading ,one of the sensors isnt giving a reading i would assume and once you find it this will reset the whole unit as soon as you drive the car 200mts and not before ,disconnecting battery and some fancy code reader will not reset the ABS only when all sensors are giving a reading will it go out .
3/12/2011 8:08:05 PM •
1997...
•
Answered
on Mar 12, 2011
Not finding what you are looking for?