Top 10 1993 Dodge Dakota Questions & Answers

1993 Dodge Dakota Logo

Question

  • 2,630 People Helped

I need a firing order diagram for a 93 Dodge

I need a firing order diagram for a 93 Dodge Dakota 3.9L V6

Posted by on

Answer

  • Most Helpful of 1 Answers

Hope this helps you.

762453a.gif

Posted on Sep 17, 2010

Question

  • 1,875 People Helped

i need a serpentine belt diagram for a 1993 dodge

i need a serpentine belt diagram for a 1993 dodge dakota...3.9 V6...without A/C

Posted by on

Answer

  • Most Helpful of 1 Answers

10_1_2011_11_40_55_pm.jpg

Fig. Accessory serpentine belt routing-3.9L, 5.2L and 5.9L LDC gasoline engines IMAGE LINK

Hope helps (remember to rating this free amswer)/

Posted on Oct 01, 2011

Question

  • 1,823 People Helped

need to replace blower motor on v6 93 dodge dakota

need to replace blower motor on v6 93 dodge dakota where is it

Posted by on

Answer

  • Most Helpful of 2 Answers

Under the glove box
You can get to it fairly easily

The Blower Resistor in the firewall may be your
problem.
They rust out. Two screws,above the
A/C Valve

Posted on Dec 19, 2010

Question

  • 1,684 People Helped

Windshield wipers don't work but the motor runs . 93 Dodge Dakota

How do you get to the windshield wiper bushings in 93 Dodge Dakota ?

Posted by on

Answer

  • Most Helpful of 1 Answers

remove wiper arms and then you can raise the hood to remove screws that hold down the vent panel.
now carefully remove vent panel.

Posted on Jan 09, 2010

Question

  • 1,587 People Helped

where is the crankshaft sensor on a 1993 dodge dakota located

how to replace it

Posted by on

Answer

  • Most Helpful of 1 Answers

It is located on the top of the bell housing at the rear of the engine towards the passenger side. Not fun to get to, but only has one 10mm head bolt holding it to the engine block and a rubber O-Ring that you will need to break loose. Make sure you get all of the old O-Ring out of the block and put a thin coat of lubricant on the new one when installing to help it go in.

Posted on Apr 18, 2016

Question

  • 1,526 People Helped

1993 Dodge Dakota Windshield wipers stopped

1993 Dodge Dakota Windshield wipers stopped working suddenly. The motor still works, the wipers had lost their adjustment and were slamming the trim on the windshield last couple weeks. Is there a common bushing if stripped would stop them or if if one goes, will it bind up both from working? I was hoping to find a diagram of what the linkage looks like before popping the cowling off. thanks.

Posted by on

Answer

  • Most Helpful of 1 Answers

There are bushings that go bad. They are available from a parts store. Ask or look under the HELP! section. the cowl panel will need to come off. replace ALL of the bushings.

Posted on Oct 28, 2009

Question

  • 1,461 People Helped

fuse box diagram 1993 dakota

fuse box diagram

Posted by on

Answer

  • Most Helpful of 1 Answers

Fuse block diagram

Posted on Jul 26, 2010

Question

  • 1,443 People Helped

Headlights sometimes cut out on a 1993 Dodge Dakota pickup

I have a 1993 Dodge Dakota sometimes the headlights cut out. I have changed the headlight switch and the hi/low beam switch.

Posted by on

Answer

  • Most Helpful of 1 Answers

you may have a bad ground wire up by the head lights the ground spot should be with in a foot of one or the head ligghts

Posted on Aug 27, 2009

Question

  • 1,435 People Helped

re: 1993 Dodge Dakota, where might I find the fuel

re: 1993 Dodge Dakota, where might I find the fuel pump reset button or inertia switch? Thank you.

Posted by on

Answer

  • Most Helpful of 1 Answers

  • You have an Automatic Shut Down Relay or "ASD Relay" not so much a "switch." The ASD relay inside the power distribution center which is under the hood on the left corner of the engine compartment. Under the lid is a legend that will pinpoint it's location in said box. I would look at this if your having problems with the fuel pump. Should you need to replace the pump the tank must be dropped for this vehicle.


11_7_2011_9_48_17_pm.gif


  • Hope this helps.

Posted on Nov 07, 2011

Question

  • 1,253 People Helped

how do i remove the steering column cover to get

how do i remove the steering column cover to get at the ignition tumbler on a 1993 dodge dakota

Posted by on

Answer

  • Most Helpful of 1 Answers

CAUTION Disconnect and isolate the negative (ground) battery cable. This will disable the air bag system. Failure to disconnect the battery could result in accidental deployment and possible personal injury. Allow the system capacitor to discharge for two minutes then begin air bag system component removal. To install:

  1. Engage the electrical connectors to the ignition switch and make sure the switch locking tabs are fully seated.
  2. Before attaching the ignition switch to a tilt steering column, the transmission shifter must be in the PARK position. Also the park lock dowel pin and the column lock flag must be properly indexed before installing the switch as follows:
    1. Place the transmission shifter in the PARK position
    2. Place the ignition switch in the LOCK position. The switch is in the lock position when the column lock flag is parallel to the ignition switch terminals.
    3. Position the ignition switch park lock dowel pin so it will engage the steering column park lock slider linkage.
    4. Apply a light coating of grease to the column lock flag and the park lock dowel pin.
  3. Place the ignition switch against the lock housing opening on the steering column. Ensure that the ignition switch park lock dowel pin enters the slot in the park lock slider linkage in the steering column.
  4. Install the retaining bracket and ignition switch mounting screws, then tighten the screws to 22-30 inch lbs. (3-4 Nm).
  5. If the vehicle is equipped with a tilt steering column, install the tilt lever.
  6. With the key cylinder and the ignition switch in the LOCK position, insert the key cylinder into the ignition switch until it bottoms.
  7. Insert the ignition key into the lock cylinder. While pushing the key cylinder in toward the ignition switch, rotate the ignition key until the end of travel.
  8. Install the retaining screw into the bracket and lock cylinder. Tighten the screw to 22-30 inch lbs. (3-4 Nm).
  9. Install the steering column covers, then the tilt lever, if equipped.
  10. Connect the negative battery cable.
  11. Check for proper operation.


ec3f7ac.jpg

eff2c5f.jpg

72e2667.jpg

7a1362b.jpg

Posted on Jul 31, 2010

833 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2001 Dodge Dakota
2001 Dodge Dakota

995 Questions

1998 Dodge Dakota
1998 Dodge Dakota

851 Questions

1997 Dodge Dakota
1997 Dodge Dakota

694 Questions

1995 Dodge Dakota
1995 Dodge Dakota

711 Questions

1992 Dodge Dakota
1992 Dodge Dakota

605 Questions

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

1993 Dodge Dakota Dakota

  • 1993 Dodge Dakota Dakota

Most Popular Question

1993 dakota recently u joint break used

  • Cars & Trucks
Loading...