20 Most Recent 1994 Oldsmobile Cutlass Supreme Questions & Answers


youve got a bad mastercylinder

1994 Oldsmobile... | Answered on Mar 30, 2019


Sounds like you are not getting enough current from the battery to the starter. If your battery is fully charged, make sure the the battery cables are tight and corrosion free (baking soda & vinegar will clean the terminals, rinsed with clear water afterwards) and make surw connections on the starter are tight. There is also a starter relay in the circuit that could be bad. You could use booster cables to connect battery direct to the starter to see if it turns the engine over, but make sure polarity is correct. Put one end of the booster cable on the the plus side of the battery, then take the other end and touch the plus (+) side of the starter. If engine turns over (it will not start) then problem is either cables, connections, or starter relay. If it doesn't turn over, I suspect the battery itself or the starter.

1994 Oldsmobile... | Answered on Dec 31, 2017


Also adjust the passenger wiper, similar to the way you adjusted the driver side.

1994 Oldsmobile... | Answered on Dec 03, 2017


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

1994 Oldsmobile... | Answered on Oct 30, 2017


Number 4 at the top is rod for release. I couldn't get everything in one picture. It appears to me, you need to remove door panel and then check everything.
door-xj34j5mzwk2nlgg3up1hex4k-4-0.jpg

1994 Oldsmobile... | Answered on Oct 08, 2017


007 Idle Speed Problems Scan Data for Idle Hooking up a scan tool that can view engine sensor data is the way to find these type problems .

1994 Oldsmobile... | Answered on Oct 03, 2017


These are called belt weather or sealing strips. I think the parts you are looking for are 12503936 and 37, but they are discontinued parts. Good luck finding them - try auto wreckers (online search).

1994 Oldsmobile... | Answered on Jun 14, 2017


Has the ECM been scanned? Read the live readings from the sensors to see if u have any direction of the problem. Maybe even diagnostic codes. Coolant sensors are known for this issue too. Take an emissions reading & read the emissions. Good Luck

1994 Oldsmobile... | Answered on May 06, 2017


Go to any auto zone or parts store and you can borrow a puller to remove the harmonic balancer. Try to get a repair manual to assist you in the removal procedure.

1994 Oldsmobile... | Answered on Nov 02, 2016


3 on each side of the block(under to car to see them) and 2 between the engine and transmission.

1994 Oldsmobile... | Answered on Sep 18, 2016


It's mounted in the right rear notch of the air intake by the fire wall or on the fire wall in that general location. with a vacuum line attached. That is standing in front of the car at the rear top edge of the manifold. Look it up on parts geek you can look at the enlarged picture to see what yo are looking for.

1994 Oldsmobile... | Answered on Jul 28, 2016


Power comes from headlamp / dimmer switch . Go here for free wiring diagrams http://bbbind.com/free_tsb.html Enter vehicle info year ,make , model ,engine size ! Under system click on lighting then under subsystem click interior light dimming .

1994 Oldsmobile... | Answered on May 30, 2016


hi.you elimanated all the firing problems i would say try the feul side it can be a dirty feul filter or a faulty injector it can be injector wires or air mass meter or a leak in the intake manifold I will say start with the feul filter.hope this helps

1994 Oldsmobile... | Answered on Jan 17, 2016


5 quarts maybe 6 with filter

1994 Oldsmobile... | Answered on Dec 02, 2015


Check fuses , they operate on different circuits, ie ignition or battery dependant on switchwork. But unlikely to be a short in indicator circuit seen as 4way works fine but still may be a fault in a shared circuit . You may be down another electrical componant but are unaware at the moment ! Good luck

1994 Oldsmobile... | Answered on Nov 12, 2015

Not finding what you are looking for?
1994 Oldsmobile Cutlass Supreme Logo

772 questions posted

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

Jonah Oneal

Level 3 Expert

14092 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Cutlass Supreme Oldsmobile

  • Cutlass Supreme Oldsmobile

Most Popular Question

replace oring distributor dummy port 3 4

  • Cars & Trucks
Loading...