Top 20
1989 Mercedes-Benz Mercedes Benz 500 Class Questions & Answers
Rear end bounces can
Yes, you can install standard shocks, like
http://www.amazon.com/Bilstein-Shock-1985-MERCEDES-B46-1184/dp/B0007M3VW0
6/6/2011 2:29:52 PM •
1989...
•
57 views • 0 helpful votes
Diagram 500 sec engine
http://www.youtube.com/watch?v=FpcrnlrZ41k
Check the video in the above link and see if it is helpful for you...
9/20/2010 4:43:19 PM •
1989...
•
529 views • 2 helpful votes
How to remove a drive belt from my mercedes 560
Not familiar with your Merc. This is general info. My porsche has a mecanical belt tensioner down low under the engine off the ground. Toyota has a spring charged piston pushing a belt tensioner wheel. Most other cars I've worked on had a pivoting alternator. If your car has a flat serpentive belt then it probaly has a spring loaded tensioner. If it has Vee belts then something sets the tension mechanically at install. Good luck!
3/17/2010 3:16:13 AM •
1989...
•
351 views • 0 helpful votes
I recently bought an 1983 500SL. car had been
Sounds like you have too much fuel going to the injectors. Your car has a CIS fuel injection system that relies on mechanical inputs do decide how much fuel to send to each injector. One of two things has likely happened. Either the plunger in the bottom of the fuel distributor is stuck up, or the diaphragm in the fuel distributor is broken. The first is easy enough to check if you can get the fuel distributor(the aluminum block on top of the engine with all of the fuel lines coming out of it) out. The plunger comes out of the bottom center. You should be able to push it in and watch is slowly spring back out. If not it needs to be removed and cleaned, but that's not just a straightforward job. Look online for videos on fuel distributor repair to decide if you want to tackle this. Diaphragm failure is harder to diagnose. If you get there it might be best to look for a rebuilt fuel distributor. A third possibility is that the fuel return line from the fuel distributor back to the tank is clogged, you should be able to easily push air through the line into the tank after you remove the fuel filler cap. Good Luck.
Cl 500 shock absorber ( front left ) diagnostick
go to each corner of the car. push the car down and up a couple of times to try to get it going up and down as best you can then let go. The car should return to normal in one movement not bounce up and down.
Shocks may be expensive but besides a more comfortable ride they are a safety feature because they keep your wheels on the ground. Bad shocks let your car bounce - if you hit your breaks the car will bounce and on the up bounce the wheels can skid and it takes longer to stop.
2kg sds fault
have a coolant system pressure test done to determine any leaks. have a compression test done to check for head gaskets and cracks.. Have a flow test done to determine if cores are blocked. Check radiator cap for correct operation. Check return hose to reservoir to ensure it is air tight and allows coolant to be drawn back to radiator when cooling down
Driver side of 2003 mercedes e500 wont rise
The easiest fix is to hook up a scanner on the suspension test plug. This will give you a test to each sensor. Some models may even record a history of performance.Underneath the car, someone can use soapy water and spray the air lines and suspension bags to test for leaks. There are venting solenoids on each wheel to level the car and a Master solenoid called a "dump" valve to release all of the air The system is tied into the doorjam and trunklid switches which must be closed to allow the system to work. Escaping air should be easy enough to find.
Speadometor not working
If you have an electric dash you may wanna check fuses first. If there is a fuse blown change it. if there's no fuse for it and, everything else in the cluster works, you may wanna have your speed sensor checked(in both) digital and regular dash clusters
Rear rotor replacement for a
YOU NEED TO SAFELY RAISE SUPPORT REAR OF VECHICLE ON JACKSTANDS. MAKE SURE VECHICLE PARKED ON SOLID LEVEL GROUND. YOU NEED TO SIPHON JUST A LITTLE BRAKE FLUID OUT OF THE MASTERCYLINDER.BECAUSE YOU NEED TO USE LARGE C - CLAMP TO COMPRESS FORCE PISTONS BACK IN THE CALIPER BORES USING LARGE C - CLAMP DOING THIS WILL ALLOW YOU ENOUGH ROOM INSTALL NEW REAR BRAKE PADS.TO REMOVE REAR PADS ONCE YOU COMPRESS PISTON BACK IN THE CYLINDER BORE. YOU CAN TO REMOVE REAR BRAKE PADS BY REMOVING RETAINING PINS IF EQUIPPED OR BRAKE PADS HELD IN PLACE BY RETAINING BOLTS.ONCE YOU HAVE NEW REAR BRAKE PADS INSTALLED.PLACE MASTERCYLINDER COVER BACK ON TOP OF MASTERCYLINDER THEN PUMP BRAKE PEDAL TO SEAT NEW REAR BRAKE PADS AGAINST THE ROTOR UNTIL BRAKE PEDAL FEEL FIRM AND SOLID.THEN RECHECK BRAKE FLUID LEVEL IN BRAKE MASTERCYLINDER ADD LITTLE MORE FLUID IF NEED DONT OVER FILL MASTERCYLINDER.
Not finding what you are looking for?