20 Most Recent 1999 Dodge Neon - Page 4 Questions & Answers


u probly disconnectd a hose or wire while fixn ur ride--go bac and inspect--listen for vacuum leaks

1999 Dodge Neon | Answered on Dec 01, 2012


TRY REPLACING THE TEMP SENSOR

1999 Dodge Neon | Answered on Nov 26, 2012


The Oil in your engine might be low check and make that you have and it's in proper level per your engine dipstick.

1999 Dodge Neon | Answered on Nov 09, 2012


The chatter is due to low voltage. Check all the connections. The battery may have corrosion that lowers the voltage.

1999 Dodge Neon | Answered on Oct 21, 2012


That proves my point that flushing is not a good idea

The flushing is not your problem entirely
It caused an already slipping transaxle to slip,
to where you can no longer use it

Any trans shop would have test driven & asked questions
& not changed the fluid

You need a complete rebuild or reman

NO FIX

The fluid change cause the already burnt clutches to
not work at all due to the different oil

Only the old dirty oil had the ability to lock up
the clutches

1999 Dodge Neon | Answered on Oct 03, 2012


make sure the flywheel is not on backwards, arter that is clear be sure to tighten bolts a little at a time using a star pattern until full torque is reached in other words dont tighten fully in consecutive order this will cause the flywheel to be off centered even if it doesnt look like it

1999 Dodge Neon | Answered on Jul 04, 2012


  • 1 Park your Neon on a level surface. Engage the parking brake. Open the hood and loosen the bolt on the negative battery cable terminal and pull the cable from the battery.

  • 2

    Remove the Neon air filter by undoing the side clips and lifting the cover of the air filter off. Pull the air filter from the bracket. Undo the clip on the air filter hose and pull the hose off the inlet. Use a socket wrench to loosen and remove the four bolts holding the air filter bracket in place and pull the bracket from the engine

    3

  • Locate the camshaft position sensor. It will be at the rear of the cylinder head, centered on where the air filter housing was about midway down. It will look like a black plastic square (4"x4") and have four bolts holding it to the engine.

  • 4

    Disconnect the wiring of the sensor from the wiring harness feeding into the car's electrical system. Press in the tabs at the sides of the connector and pull the two halves apart to do this.

  • 5

    Remove the four bolts holding the sensor in place and remove the sensor from the engine.

  • 6

    Clean the engine of any gasket material from the old sensor by scraping the surface gently with a paint scraper.

  • 7

    Install the new sensor by placing it in the same position as the old one, replacing the bolts and then connecting the wiring harness. Replace the air filter bracket, hose, filter and cover. Reconnect your battery and you are done.



  • buy F150 Parts.

1999 Dodge Neon | Answered on Jun 03, 2012


Replace Drums, shoes, wheel cylinders and brake hardware.

1999 Dodge Neon | Answered on Apr 10, 2012

Not finding what you are looking for?
1999 Dodge Neon Logo

321 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2002 Dodge Neon
2002 Dodge Neon

839 Questions

2004 Dodge Neon
2004 Dodge Neon

733 Questions

2003 Dodge Neon
2003 Dodge Neon

727 Questions

2005 Dodge Neon
2005 Dodge Neon

688 Questions

2000 Dodge Neon
2000 Dodge Neon

598 Questions

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Neon Dodge

  • Neon Dodge

Most Popular Question

clock spring

  • Cars & Trucks
Loading...