1993 Chevrolet S-10 - Page 5 - Answered Questions & Fixed issues

no but changeing the troqure converter will

1993 Chevrolet... | Answered on Jan 21, 2011 | 42 views

possible corosion in the socket bad ground is there a trailer package hooked up sometimes corosion builds up and makes a bad contact in the harness

1993 Chevrolet... | Answered on Jan 06, 2011 | 210 views

A good general tune up might do wonders. Your complaint is a little to vague to try and be specific with an answer.

Try plugs, wires, cap &rotor (if so equipped) along with air and fuel filters

1993 Chevrolet... | Answered on Dec 31, 2010 | 32 views

Hello taysma.

Under the hood, look to the left as you look in towards the firewall.
You will see the blower fan motor there. Turn it on if you are unsure what it looks like and listen.
No need to start the engine, just turn the key to the On position.
To the right of the motor you will see a plug with several wires on it. That will be the resistor.
Buy the new one first so you know what it looks like.
Easy to replace and not expensive.

Thank you for using FixYa.


1993 Chevrolet... | Answered on Dec 30, 2010 | 140 views

looks like an electrical short

1993 Chevrolet... | Answered on Dec 29, 2010 | 72 views

Hello somethindark: My name is Roger and I will help you. You must have a fuel pressure of 9 to 13 psi any thing less the engine will not start. Look for a restriction in the fuel line between the fuel tank and the throttle body. Could be e bent on kinked fuel line. or a bad hose at the tank area. If this was a salvage yard pump or even a new one it could be bad. Check to make sure you have the pump wired properly. If wired in reverse the pump will turn backwards and not pump the correct pressure.Also if you pull the pump check the connection at the pump if it has a plug to pump in the tank make sure the plug is not damaged. A damaged plug could reduce voltage causing a slow running fuel pump. Should you need further help please just ask. Please rate the answer. Thank You for using and trusting Fix Ya for your repair questions. Roger

1993 Chevrolet... | Answered on Dec 23, 2010 | 99 views

If your talking about the Check engine light. You will need a CHEVROLET OBD I code reader. the auto makers used their own style of ports and language until OBD II in 1996. The code reader can be purchased at most auto parts stores and it isn't very expensive.

1993 Chevrolet... | Answered on Dec 22, 2010 | 334 views

rear end main bearing

1993 Chevrolet... | Answered on Dec 12, 2010 | 44 views

you will have to remove the interior door panel inside to access the linkage to open the door you, Check the door handle if it is broken inside and out. The outside door handle is bolted on the inside one may have to drill a rivet out. You can use a bolt and nut to reinstall it make sure it isnt too long. Or you can rivet it back in. You will have to inspect the linkage and check out the adjustment and the plastic retainers sometimes you need to replace those they will come with new handles.The window has to be up to access the outside door handle from the inside.

1993 Chevrolet... | Answered on Dec 10, 2010 | 186 views

Relay contacts may have fused. Try swapping it with another 5-terminal relay in the box (under the hood).


1993 Chevrolet... | Answered on Nov 25, 2010 | 157 views

Check the fuel pressure. Even if it's running it may not be producing pressure. See if you can keep it running on starting fluid or carbuerator cleaner. If so replace the pump.

1993 Chevrolet... | Answered on Nov 23, 2010 | 198 views

it sounds like you transfered the problem , did you change anything from one transmission to the other?....also make sure the transmission is getting powered up
to check this open the key and test pin "e" pink wire for voltage at transmission connector

1993 Chevrolet... | Answered on Nov 22, 2010 | 80 views

well,if you have the extra 200 go for it !!!!

1993 Chevrolet... | Answered on Nov 19, 2010 | 42 views

If this is a 4.3 then it is correct. When both dots are lined up together on the timing gears, number one will be at the begining of the intake stroke which would make cylinder 4 at the begining of the power stroke, which is where the spark occurs.

1993 Chevrolet... | Answered on Nov 19, 2010 | 109 views


1993 Chevrolet... | Answered on Nov 01, 2010 | 1,131 views

In your truck the firing order is 1-2-3-4-5-6. Number 1 cylinder is on the pass side front. So it is numbered on the pass side from front to rear 1-3-5 and on the drivers side front to rear 2-4-6. The distributer rotor will turn clockwise looking at it from the grill of the truck. Number one plug wire in the cap should be at the 7 o'clock location. going around the cap clockwise starting in the 7 o'clock position, the wires should run 1-2-3-4-5-6.. Note: The 2.8L v6 #1 cylinder location is opposite of the 4.3L v6 or any of the v8's. Hope this helps.

1993 Chevrolet... | Answered on Oct 17, 2010 | 1,844 views

1-6-5-4-3-2 The driver side is odd and the passenger is even. front of the motor is low number cylinder going up to the firewall

1993 Chevrolet... | Answered on Aug 16, 2010 | 386 views

Hope this helps.


1993 Chevrolet... | Answered on Jul 22, 2010 | 3,240 views

You would have to get in between the grill and the radiator and somehow release the inner catch. This can be done but it's a tight fit.

1993 Chevrolet... | Answered on Jul 20, 2010 | 64 views

Not finding what you are looking for?
1993 Chevrolet S-10 Logo

336 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Chevrolet Experts


Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides