changing wires got wires mixed up need proper firing order to distribiture cap
991 Chevy S10 firing order
The firing order for a Chevy s10 depends on which engine you have.
1.9L engine the firing order is: 1-3-4-2 . Distributor rotates counterclockwise.
2.0L engine the firing order is: 1-3-4-2 . Distributor rotates clockwise.
2.5L engine the firing order is: 1-3-4-2 . Distributor rotates clockwise.
2.8L engine the firing order is: 1-2-3-4-5-6 . Distributor rotates clockwise.
4.3L engine the firing order is: 1-6-5-4-3-2 . Distributor rotates clockwise.
Posted on Jan 09, 2010
chevy s10 1991 4 wheel drive will not engage at the axle in hi or low
There is a vaccuum operated switch located on the transfer case that sends vaccum to the accuator that pulls a cable that locks the front end in. Check for vac coming in and out of this switch if no vac out replace it. This switch is a very common problem. You can find them at most parts stores in the help section #49315. please rate.
Posted on Dec 08, 2008
i need diagram for firing order on a 91 s10 blazer 4.3 2wd
For the 1991 Chevrolet S10 Blazer 4.3 V6, Both: 2WD AND 4WD:
Firing Order:
1-6-5-4-3-2
Cylinders:
.......(back).......
|..6..|.......|..5..|
|..4..|.......|..3..|
|..2..|.......|..1..|
......(front)
Distributor:
....(back)
(+).4...3
5...........2
..6...1..(+)-screw
.....(front)
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!
Posted on Apr 26, 2010
firing order for 91 chevy s10 2.8
Here is the firing order diagram for that vehicle and engine.
Posted on Jul 31, 2010
I have a 1991 Chevy S10 2.5 L4, do you have a wiring diagram for the distributor cap and spark plug wires?
firing order 1342, distributor, clockwise rotation.
Posted on Aug 26, 2009
1991 Chevy s10 2.8 5 spd speedometer not working :(
check the fuses, mine did the same thing, I replaced the fuse in the fuse panel and it works great now.. easy fix
Posted on Mar 15, 2009
2002 Chevy S10 4.3 02 sensor bank 2/sensor 1 code P0155.
Hi My name is Robin,
I have recently replaced the fuel pump and fuel filter on this truck. Before any of those repairs were made I was getting the above mention code and my service engine light is on. Replace the sensor and drove it about 100 miles. The same code popped back up again. Any ideas?
problem is in replacement of O2 senser try again to put it.
take a help from a link>>
http://www.popularmechanics.com/automotive/how_to/4219927.html?page=2
happy to help u any time.
Thanks for using FixYa.
Posted on Jan 28, 2009
what is the spark plug gap for a chevy s10 pickup?
Mine is a 4 cyl & its 65k.. 94,,,,
Posted on Apr 07, 2011
I just need to know how to set the time on my radio clock.
It really depends on the type and model of your radio. Below is the generic clock set proceedure for the most popular radio at that time.
Hope this works for you.
Regards,
To set the clock, just:
Press the SET button. The word SET will light up in the VF display.
Within 5 seconds, press and hold the SEEK button until the correct hour
appears on the display.
Then, press and hold the SCAN button until the correct minute appears
After you set the time, the word SET will remain in the VF display for a
on the display.
few seconds.
Posted on Jun 18, 2009
how do i remove a starter from a 1991 chevy s10 4.3 p/u
I have a 93 s-10...think its the same...disconnect the neg terminal of the battery first...then crawl under the vehicle and look up near where the transmission and the engine connect together..on the passenger side should be the starter..there are two bolts holding the starter in...if you have enough room try to remove the positive battery cable first from the starter before trying to remove the mounting bolts..there should be a small wire that goes to the trigger lead on th solenoid...be sure to note where it goes..as this is the lead that hooks to the ignition switch to crank the starter
Posted on Jun 10, 2011
694 questions posted
Usually answered in minutes!
1,473 Questions
904 Questions
790 Questions
747 Questions
686 Questions