20 Most Recent 2004 Chevrolet Blazer Questions & Answers

CPS. Lot of details in the link. https://www.google.com/search?q=2004+Chevy+Blazer+crankshaft+Position+Sensor+location ..

on top of starter

Engine Compartment (#STARTER) :https://fuse-box.info/chevrolet/chevrolet-blazer-1996-2005-fuses-and-relay#2003_2004_2005

If the rest of your lights are OK, there may be a dead spot on the dash dimmer control (near the headlight switch). Cycle the control a few times to see if that fixes it. Otherwise, check the fuses at the left end of the dash.

you can get guide from many sites.. i know few error codes/ fault codes, wiring diagrams, schematic diagrams, torque specs, engine info, switches functioning, assemble, disassembly, complete refurbish, repair, installation every single thing is covered within seconds u can get the access and it's totally illustrative complete

How To Diagnose P0128 Faulty Thermostat

Car Repair Manuals Chilton Haynes Bentley Haynes Manuals Do It Yourself and DIY Auto Repair by ChiltonDIY

Under hood, left side of dash by the door light switch, under the dash high up on the left

If plug an plug wire has been replaced , an dist. cap an rotor an problem is still there ,maybe a fuel injector problem . Perform the fuel injector coil test. Refer to Fuel Injector Solenoid Coil Test . A fuel injector coil winding resistance that is too high or too low will affect engine drivability. A fuel injector control circuit DTC may not set, but a misfire may be apparent. The fuel injector coil windings are affected by temperature. The resistance of the fuel injector coil windings will increase as the temperature of the fuel injector increases. Diagnostic Aids ?€¢ Monitoring the misfire current counters, or misfire graph, may help to isolate the fuel injector that is causing the condition.

?€¢ Operating the vehicle over a wide temperature range may help isolate the fuel injector that is causing the condition.

?€¢ Perform the fuel injector coil test within the conditions of the customer's concern. A fuel injector condition may only be apparent at a certain temperature, or under certain conditions.

2 Observe the ECT Sensor parameter with a scan tool. Is the ECT Sensor parameter within the specified range? 10-32?°C (50-90?°F) Go to Step 3 Go to Step 4 3

1. Disconnect the multi-way harness connector of the fuel injectors.
2. Measure the resistance of each fuel injector between the ignition 1 circuit and the fuel injector control circuit, at the multi-way connector with a DMM. Refer to Testing for Continuity in Wiring Systems.

Is the resistance within the specified range for each injector? 11-14 ohms Go to Fuel Injector Balance Test with Special Tool or Fuel Injector Balance Test with Tech 2 Go to Step 6 4

1. Disconnect the multi-way harness connector of the fuel injectors.
2. Measure the resistance of each fuel injector between the ignition 1 voltage circuit and the fuel injector control circuit, at the multi-way connector with a DMM. Refer to Testing for Continuity in Wiring Systems.
3. Record each fuel injector resistance value.
4. Subtract the lowest resistance value from the highest resistance value.

Is the difference equal to, or less than, the specified value? 3 ohms Go to Fuel Injector Balance Test with Special Tool or Fuel Injector Balance Test with Tech 2 Go to Step 5

bad battery connetion

Heater cores don't go out ! They leak an in which case you would have coolant on the passenger side floor ,your windshield would fog up . There can get plugged , because someone mixed regular coolant with GM Dex-cool . Check you coolant is it a rust looking color ? Vehicle wont start ? how ? crank - no start or a no crank - no start ? When you turn the key to the start position does the engine spin or nothing !

The smog check requires a visual inspection of your check engine light. It has to come on for a bulb check at startup to make sure it's working. But, the light must go out after starting the engine(it cannot stay on after the engine starts during a smog check). If the check engine light fails either of these two tests, the vehicle will fail the smog check inspection.
You need to have the cause of your inoperative check engine light diagnosed and repaired.

I'd have a few things checked out by a pro since it sounds like this can be dangerous. 1st is your front Sway bar and bushings, have your rack and pinion checked out by a pro. Also check your wheel hub bearing assemblies. Final thought, make sure your 4wheel drive is NOT engaged, should be in 2 wheel hi. If in 4 wheel drive while on pavement, all turns will feel squirley and isn't good for your drive train.

Hazard and Turn Signal Flasher Replacement Open the glove box to expose the glove box retaining tab (1). Lift the retaining tab and allow the glove box to hang freely. Using a suitable flat-bladed tool, release the plastic retainer that retains the hazard/ turn signal flasher (1) to the C203 body harness connector (2) . Remove the hazard/ turn signal flasher (1).

Take it back. Who built the transmission?