1995 Dodge Ram - Page 7 - Answered Questions & Fixed issues
I have a 1995 Dodge Ram 1500 4 x 4, I need to
Remove wheel....remove brakes....three bolts behind the hub (9/16" 12pt socket)....1 11/16" nut in center of hub needs to be removed. You will need a slide hammer type puller to hook onto the hub for removal. (you should replace the hub...prone to go bad)....axle will now slide out through opening where the hub was.
11/7/2009 12:16:38 AM •
1995 Dodge Ram
•
Answered
on Nov 07, 2009
•
308 views
I changed th pick up coil in my distributor on my
yes, tap engine over until # 1 is at top dead center which would be ) on the gauge on harmonic balancer.find #1 on your cap on the distributor, at top dead center on #1 the rotor in the distributor should be at #1when the diistributor is all the way in and down in hole. then you should be close enough to time it with a light.
10/12/2009 2:16:00 PM •
1995 Dodge Ram
•
Answered
on Oct 12, 2009
•
94 views
How to install rear window on 1995 dodge ram
Chrysler Full-Size Trucks 1989-1996 Repair Guide
Stationary Side or Rear Window
(see Figures 1, 2 and 3)
You'll need an assistant for this job.
-
Remove the moldings surrounding the glass.
-
Have your assistant stand outside and support the glass.
-
Working from the inside truck, start at one upper corner and work
the weatherstripping across the top of the glass, pulling the
weatherstripping down and pushing outward on the glass until your
assistant can grab the glass and lift it out.
Fig. 1: Work the weatherstrip seal in until fully seated
-
Remove the weatherstripping from the glass.
Fig. 2: Exploded view of the vent window mounting-Dakota models
Fig. 3: Exploded view of a common rear window mounting
To install:
-
Clean the weatherstripping, glass and glass opening with solvent to remove all old sealer.
-
Apply liquid butyl sealer, in the glass channel of the weatherstripping and install the weatherstripping on the glass.
-
Apply a bead of sealer to the opening flange and in the inner flange crevice of the weatherstripping lip.
-
Place a length of strong cord, such as butcher's twine, in the
flange crevice of the weatherstripping. The cord should go all the way
around the weatherstripping with the ends, about 18 in. (457mm) long
each, hanging down together at the bottom center of the window.
-
Apply soapy water to the weatherstripping lip.
-
Have your assistant position the window assembly in the channel from the outside, applying firm inward pressure.
-
From inside, you guide the lip of the weatherstripping into place
using the cord, working each end alternately, until the window is
locked in place.
-
Remove the cord, clean the glass and weatherstripping of excess sealer and leak test the window.
-
Install the moldings.
I hope help you with this (remember rated this help) Good luck.
10/6/2009 8:59:01 PM •
1995 Dodge Ram
•
Answered
on Oct 06, 2009
•
2,027 views
How to fix reverse lights on a 2002 1500 4x4 dodge
There should be a switch on the trans that may have a bad connection or has gone bad. I am guessing your trans (like most) is an automatic.
I see yours is a 4x4. If you have been working on the rig or been out off road, then you may have clipped or bumped a connection.
I'm not sure on this year but it may be a part of the Neutral Safety Switch.
Hope this helps...
9/30/2009 8:14:34 AM •
1995 Dodge Ram
•
Answered
on Sep 30, 2009
•
243 views
Trouble starting
you may have an air leak in the petrol line, probably where the fuel pump was changed.
the car won't srpay out petrol some time's but overnight the vacum in the fuel line ****'s air in & the system is not primed.
The only way you can check this is by priming the rail first thing in the morning by turning the ignition key to the point just before starting & you should hear the fuel pump run for about 4 second's then turn off the ignotion, wait for a few sec's & turn the key to same position, it will prime again.
Do that a few times & check for petrol leak's as the fuel will run back to the tank via a pressure valve, If you see a leak then you've found where the air is getting back in if there is no leaking but the engine start's then you will have to go over all the hose clip's in the petrol system.
If not that then get back to me !
12/5/2009 7:33:15 PM •
1995 Dodge Ram
•
Answered
on Dec 05, 2009
•
182 views
1994 jeep cheokee
yo uhave a generic (unless you have an infinity sound system) speaker usually 6" round
9/17/2009 2:53:14 PM •
1995 Dodge Ram
•
Answered
on Sep 17, 2009
•
56 views
Why do i have low compression in only one cylinder
Here is a easy way to find out,its called a leakage test and here is how you can do it,bring that cylinder top dead center,you may have to remove that valve cover and make sure all valves are bottomed out.put 50 psi of air in the spark plug hole remove radiator cap air cleaner and oil fill,listen for the air comeing out.if you have air coming from your air cleaner you have a intake valve bad,do the same with the exhaust,if you have bubbles in your radiator you have a blown headgasket,if you hear alot of air comeing from your oil fill you have a problem with that piston,I hope this helps you,
9/16/2009 3:52:26 PM •
1995 Dodge Ram
•
Answered
on Sep 16, 2009
•
975 views
I have a 1995 Dodge Ram 1500 V6. When the A/C
if the compressor is cycling the problem is not the fixed orfice, it is very likely the temperature control blend door actuator has failed and the blend door is stuck in the heated air position. .
9/16/2009 3:41:24 PM •
1995 Dodge Ram
•
Answered
on Sep 16, 2009
•
443 views
95 cummins, cant get fuel to fuel filter. already
Is the lift pump on the engine and mechanical?If it is please try to put some air preasure in the tank and see if you get fuel to your filter,Or you can get a 2 gallon bucket a fill with clean fuel and run a suchtion line from the pick up pump and see if it will pick up then if it does you have a colapsed line,I hope this helps
9/6/2009 3:14:43 PM •
1995 Dodge Ram
•
Answered
on Sep 06, 2009
•
230 views
Not finding what you are looking for?