1990 Dodge Ram - Page 5 - Answered Questions & Fixed issues

0helpful
1answer

1990 Dodge Ram window van. Audible vibration noise from 60-70mpg

tires, possably needs to be balanced
7/8/2009 8:03:38 PM • 1990 Dodge Ram • Answered on Jul 08, 2009 • 294 views
0helpful
2answers

I hear a loud rumming sound towards the back under the body while

First get your wheel balance checked .... Sometimes the balance weights come off !
If that checks out ok and the tires are good then I would be checking the rear wheel bearings.
Let me know how you get on.
6/27/2009 9:24:21 AM • 1990 Dodge Ram • Answered on Jun 27, 2009 • 148 views
0helpful
2answers

No power from battery/battery has power

wires between the starter and battery most of the time you have to pull starter off and they are close to starter
4/20/2009 4:28:27 PM • 1990 Dodge Ram • Answered on Apr 20, 2009 • 122 views
0helpful
1answer

1990 dodge d150 headlights won't come on.

I think that you have to find the relay box for the headlamp and so forth relays.
4/12/2009 7:41:43 PM • 1990 Dodge Ram • Answered on Apr 12, 2009 • 372 views
0helpful
1answer

I need the firning order for a 318 dodge ram 90

This is the best info I got;
firing order is 1 8 4 3 6 5 7 2

Spark plugs should be changed one at a time to prevent mixups.
Spark plug cables should be changed one at a time to prevent mixups.
5/4/2009 5:23:48 PM • 1990 Dodge Ram • Answered on May 04, 2009 • 243 views
0helpful
2answers

Basic tune-up procedures

Check the intake manifold...the firing order on my Dakota is cast on the surface of the manifold. If it's not there, ask your parts store guy if they have the information.
4/1/2010 3:20:33 PM • 1990 Dodge Ram • Answered on Apr 01, 2010 • 390 views
0helpful
1answer

1990 Dodge Ram truck will not start, makes clicking noise.

the clicking noise is the starter solenoid, the heavy electrical contacts that supply 12 volts to the starter are burnt, you will either need to replace the starter slenoid contact set or the solenoid.
2/12/2009 7:16:57 PM • 1990 Dodge Ram • Answered on Feb 12, 2009 • 1,190 views
0helpful
1answer

1990 Dodge Ram Wiper not working

You did everything else. You have voltage going to motor,so I would say that was it.
1/27/2009 10:33:41 PM • 1990 Dodge Ram • Answered on Jan 27, 2009 • 551 views
0helpful
1answer

Engine swap lookin for a 5.9 computer #

If you told a good dealer parts person what you where trying to do they could get the correct calibration processor for you, you are dealing with a bunch of by the book parts people, can't think outside the box.
10/11/2008 3:38:46 AM • 1990 Dodge Ram • Answered on Oct 11, 2008 • 274 views
0helpful
2answers

Tranny high shifting

There is a linkage on the Loadflight A-500 transmission that travels from the throttle linkage to a lever on the transmission. Proper adjustment of this linkage controls the shift schedule of the transmission with respect to engine throttle position. This would be the most likely place to start after ensuring that your fluid level is correct.
10/5/2010 5:12:59 PM • 1990 Dodge Ram • Answered on Oct 05, 2010 • 236 views
0helpful
1answer

2016 Dodge Ram ProMaster City 2.4 L. Can you give me the cylinder head torque specs and sequence for it please?

Question edited for clarity. Question moved to Dodge Ram. https://tighttorque.com/vans/ram/promaster Torque Specs https://www.google.com/search?q=2016+dodge+ram+promaster+city+2.4+cylinder+head+torque+specs Sequence is always centre outwards and crisscrossing to the edges and normally in three tightening passes to the final torque. https://www.google.com/search?q=2016+dodge+ram+promaster+city+2.4+cylinder+head+torque+sequence ..
11/10/2023 8:48:39 PM • Dodge Ram Cars &... • Answered on Nov 10, 2023 • 45 views
0helpful
1answer

How come why my 98 Dodge ram starts and runs fine but when I switch it off it won't start back up

no ca/truckr model told at all, of many 3 or 4.no engine told and is and engine problem.the VIN digit #8 is the engine codeNO model told.ram 1500 ?, 2500, 3500 or 4000 , and not the Ram van. 1998 (4000 Mexico or Canada)no engine told one is Diesel;, 3.9 L Magnum V65.2 L Magnum V85.9 L Magnum V85.9 L Cummins turbo-diesel I6<<< ill not cover this ever.8.0 L Magnum V10does the starter motor always work correctly every time, called cranking?we get the fact it does not start. sometimesbut what is not clear, at all, is that the starter always makes this sound called cranking? or fails to do crankingsee MP3 post
5/18/2023 12:27:50 PM • Dodge Ram Cars &... • Answered on May 18, 2023 • 62 views
0helpful
1answer

2014 Dodge Ram won't seem to go into drive, only reverse and neutral?

step1 in the service manual states check levels first then make sure the shift linkage is good end to end, then scan the pcm for TCM errors. using a real scan tool OBD2 USA and more, lots more, check fuses? to the service manual pump; pressure tests PRNDL pressures each?
4/9/2023 5:25:15 PM • Dodge Ram Cars &... • Answered on Apr 09, 2023 • 116 views
0helpful
2answers

I have a 2012 Dodge Ram.. I Keep trying and eventually it starts. I have replaced the fuel pump, spark plugs, and fuel relay. Once it gets started and warms up then I have no trouble starting it.

If you're experiencing difficulty starting your 2012 Dodge Ram, even after replacing the fuel pump, spark plugs, and fuel relay, there may be several other possible causes. Here are a few things you can check:
  1. Check the Battery: A weak battery can cause starting issues, especially in colder temperatures. Check the battery voltage and consider replacing the battery if it's not holding a charge or is more than a few years old.
  2. Inspect the Ignition System: The ignition system includes the spark plugs, ignition coils, and spark plug wires. If any of these components are worn, damaged, or corroded, it could cause starting problems. Check these components and replace them as necessary.
  3. Check the Fuel System: While you've already replaced the fuel pump and fuel relay, it's possible that there is still an issue with the fuel system. Check the fuel pressure to make sure it's within the manufacturer's specifications. If it's too low, there could be a problem with the fuel filter or fuel injectors.
  4. Check the Engine Coolant Temperature Sensor: The engine coolant temperature sensor can affect the fuel system and cause starting problems if it's faulty or not reading the engine temperature correctly. Check this sensor and replace it if necessary.
  5. Check the Starter Motor: The starter motor could be failing or not engaging properly, which could cause starting problems. Check the starter motor and have it tested if necessary.
If none of these suggestions resolves the issue, it's recommended to take your vehicle to a certified mechanic or dealership for further diagnosis and repair.
2/27/2023 1:22:02 PM • Dodge Ram Cars &... • Answered on Feb 27, 2023 • 66 views
0helpful
1answer

2002 Ram Cummins A/C Compressor On/Off

Your A/C system have safety switches, IE-limit switches. You could have either low or high pressure kicking out your compressor. You need a set of gauges to tell what your issue is.
6/2/2022 5:03:23 PM • Dodge Ram Cars &... • Answered on Jun 02, 2022 • 53 views
0helpful
1answer

Red lightning bolt on 2008 Dodge Ram 5.7 hemi truck won't start, drove it to the vets came out and nothing...

The lightning bolt on the dash means that there is a problem with the electronic throttle control system in your vehicle. Get a code reader and scan the engine for any logged codes. The light may be on for a glitch and the electronic throttle control system needs to be reset. To reset the Dodge Ram throttle position sensor(TPS), You need to turn on the ignition without Your foot on the brake, so the engine doesn't start. Then press the accelerator on the floor for 15 seconds. Release the accelerator. Then turn the car off and start the engine and drive.
3/13/2022 10:56:36 PM • Dodge Ram Cars &... • Answered on Mar 13, 2022 • 654 views
0helpful
1answer

Glow plug location on a 1999 Dodge ram 1400

Partstore knows
2/19/2022 4:15:20 AM • Dodge Ram Cars &... • Answered on Feb 19, 2022 • 49 views
0helpful
1answer

Blinkers sometime work either one but blinks maybe 2 or 3 times then quits on my 2000 ram

maybe try and see if the bulbs are seated firmly in the sockets.
10/7/2021 5:54:48 PM • Dodge Ram Cars &... • Answered on Oct 07, 2021 • 51 views
Not finding what you are looking for?
1990 Dodge Ram Logo

191 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1999 Dodge Ram
1999 Dodge Ram

1,788 Questions

1994 Dodge Ram
1994 Dodge Ram

197 Questions

2004 Dodge Ram
2004 Dodge Ram

173 Questions

1998 Dodge Ram
1998 Dodge Ram

143 Questions

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...