Top 10 2002 Dodge Intrepid Questions & Answers

2002 Dodge Intrepid Logo

Question

  • 9,262 People Helped

location of camshaft sensor on a 3.5 dodge intrepid

need help

Posted by on

Answer

  • Most Helpful of 1 Answers

The Camshaft Position Sensor is installed in the Timing Belt Housing Cover above the Left Camshaft Sprocket. Below is a couple of pictures...
5e46f38.jpg

58444d6.jpg
I hope this helps you. If you have any more questions or need any more diagrams, please don't hesitate to ask...Thanks again, JShreader.

Posted on Mar 31, 2009

Question

  • 7,701 People Helped

2002 Dodge Intrepid transmission not shifting

Vehicle won't shift correctly. Start the vehicle, accelerate, shifting works but upon coming to a stop, the vehicle will not up/down shift until the vehicle is turned off and back on. My transmission shifts perfectly for about 15-20 minutes than will downshift as I am coming to a stop, and then will stay in first gear until I cut the car off

Posted by on

Answer

  • Most Helpful of 10 Answers

Lets all get together and form a class action law suit. This should be a recall. but no body has been killed yet.Our tax dollars get to bail them out so they on keep making defective products.I wounder would they except defective money for there cars.

Posted on Apr 20, 2009

Question

  • 3,960 People Helped

I need a time diagram of an 2002 dodge intrepid,

If anyone can provide a diagram of the time chain, in order to adjut the time of the 2.7 motor Dodge intrepid 2002

Posted by on

Answer

  • Most Helpful of 1 Answers

Hi there;

Here is a picture of the timing marks for the 2002 2.7L intrepid engine.


Hope this helps
Farrout!

Posted on Mar 17, 2009

Question

  • 3,719 People Helped

what is the torque for head screws and timing

what is the torque for head screws and timing

Posted by on

Answer

  • Most Helpful of 1 Answers

300M, Concorde, Intrepid, LHS, 1998-2004 - Cylinder Head
Removal & Installation
2.7L Engines

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Properly relieve the fuel system pressure.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    NOTE Place shop rags in the openings to prevent debris from entering the engine.
    Negative battery cable Accessory drive belts Crankshaft damper Intake plenum, lower intake manifold and exhaust manifold Valve and timing chain covers Coolant connections for the cylinder heads
  5. Rotate the crankshaft until the crankshaft timing mark aligns with the timing mark on the oil pump.
    WARNING Be sure the head bolts 9-11 are removed before attempting to remove the cylinder head, the head and/or block may be damaged.
    Primary timing chain Camshaft bearing caps, gradually, in the reverse order of the tightening sequence Camshafts Cylinder head bolts in reverse order of installation starting with bolts 11-9, then 8-1 Cylinder head(s)

To install:


af080a0.jpg

Fig. Camshaft bolt tightening sequence-2.7L engine

eb0ed0f.jpg

Fig. Cylinder head bolt tightening sequence-2.7L engine
  1. Thoroughly clean and dry the mating surfaces of the head and block. Check the cylinder head for cracks, damage or engine coolant leakage. Remove scale, sealing compound and carbon. Clean the oil passages thoroughly.
  2. Place a new head gasket on the cylinder block over the locating dowels.
  3. Inspect the cylinder head bolts for necking (stretching) by holding a straightedge against the threads of each bolt. If all of the threads are not contacting the straightedge, the bolt should be replaced. New head bolts are recommended.
    WARNING Due to the cylinder head bolt torque method used, it is imperative that the bolt threads be inspected for necking (stretching) prior to installation. If the threads are necked down, the bolt should be replaced. Failure to do so may result in parts failure or damage.
  4. Lubricate the bolt threads with clean engine oil, then install them.
  5. Torque the head bolts in the sequence shown in the illustration, utilizing the following steps and tightening values:
    1. Step 1: bolts 1 through 8: 35 ft. lbs. (48 Nm).
    2. Step 2: bolts 1 through 8: 55 ft. lbs. (75 Nm).
    3. Step 3: bolts 1 through 8: 55 ft. lbs. (75 Nm).
    4. Step 4: bolts 1 through 8: plus 90 degree turn using a torque angle meter.
    5. Step 5: bolts 9 through 11: 21 ft. lbs. (28 Nm).

  6. Install or connect the following:
    Camshafts, timing chain and sprockets Water connections to the cylinder head Valve and timing chain covers Crankshaft damper and torque the center bolt to 125 ft. lbs. (170 Nm) Lower intake manifold and intake plenum Exhaust manifolds Accessory drive belts Negative battery cable
  7. Fill the cooling system to the proper level.
  8. Start the vehicle, check for leaks and repair if necessary.
continue...

Posted on Apr 13, 2010

Question

  • 3,558 People Helped

what do i need to

what do i need to replace to fix error code p0700 on a 2002 dodge intrepid

Posted by on

Answer

  • Most Helpful of 1 Answers

(DTC) CODE # P0700....Transmission Control System (MIL Request) Translation: Transmission Control Module (TCM) Malfunction or Failure. P0700 Information Code The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM. This code is for information ONLY. If this code is present, check for transaxle codes. So basically, the P0700 code is telling you to check the TCM for a transaxle DTC. The TCM can not turn on the check engine light so it has the PCM do it.

I hope this helps....let me know if I can assist further !!

Posted on Feb 21, 2011

Question

  • 3,496 People Helped

How do I replace the coolant air bleeder assembly

How do I replace the coolant air bleeder assembly on a 2002 Dodge Intrepid

Posted by on

Answer

  • Most Helpful of 2 Answers

THE BLEEDER IS PART OF THE UPPER HOSE HOUSING. THE ENTIRE HOUSING MUST BE CHANGED WITH A NEW ONE. THIS IS NOT AN EASY DO-IT-YOURSELF KINDA JOB. IT SHOULD BE REPLACED BY A PROFESSIONAL. HOPE THIS HELPS. PLEASE KEEP ME POSTED. THANKS FOR AN HONEST RATING AND FOR USING FIX-YA, GOOD LUCK

Posted on May 16, 2009

Question

  • 2,906 People Helped

leaking red fluid

there is a part under the hood toward the front of the car that is leaking red fluid does anyone know what could be the problem or at least what part that is?

Posted by on

Answer

  • Most Helpful of 3 Answers

The red fluid is transmission fluid, check the transmission fluid level, if it get's to low the transmission will burn out and your looking at a expensive job.
The fluid could be leaking from the transmission cooler line to the radiator in front of the car. Have it repaired and keep an eye on the fluid level to the transmission. Note: transmission fluid is flammable and may catch fire if slashed on to any hot area's like the exhaust.
Good luck and hope this helps.

Posted on May 26, 2009

Question

  • 2,894 People Helped

como instalar cadena de tiempo

como instalar cadena de tiempo de dodge intrpid 2004

Posted by on

Answer

  • Most Helpful of 1 Answers

tengo un problema con un 2007 dodge charger nose como los puntos de las cadenas pequenas los ejes de las cabezas

Posted on Dec 07, 2012

Question

  • 2,622 People Helped

how do you set the cam timing on a dodge 2.7

how do you set the cam timing on a dodge 2.7 liter, between the exhaust cam and intake cam???? HELP!!

Posted by on

Answer

  • Most Helpful of 1 Answers

Here are the diagrams for the secondary timing chains (exhaust cam - intake cam) and the primary timing chain. (courtesy of AutoZone)

10bc7b2.gif

60dbeef.gif

Posted on Feb 25, 2010

Question

  • 2,393 People Helped

coolant air bleeder

how do i change the coolant air bleeder

Posted by on

Answer

  • Most Helpful of 1 Answers

If you need to do this because the top came off, I found it to be a big job on the 2.7L V6. I initially tried to bond the top back on with no success.

To replace it, you have to remove both the upper and lower intake plenum. This device has the upper radiator hose connected in front, and the tube which runs back below the intake plenum connects to a heater hose at the rear. The hose clamp on the rear connection is very hard to get to. Unless you have a lot of mechanical experience, and a lot of patience, you may want to pay someone to do this for you. The price on the part from the dealer was about $110, as I remember.

Posted on Nov 10, 2008

1,374 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

2002 Dodge Intrepid Intrepid

  • 2002 Dodge Intrepid Intrepid

Most Popular Question

remove passenger side door panel 2002

  • Cars & Trucks
Loading...