Top 10 2006 Ford Freestar Questions & Answers

Make sure that the odometer is set to miles and not kilometers. Hold the button down (while in the regular odometer setting, not the "trip odometer" setting) until it changes to miles. The temperature display will automatically change to fahrenheit. We just figured this out today.

Before you try and push on the caliper to hard stop..When compressing the caliper it needs to be rotated at the same time it is being press in.Turn clock and push in at the same time..Hope this helps you and take your time..Have a great day

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_a3369546f8067589

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

I have 2007 only. please rate as solved if this is what you needed. good luck.

SECTION 501-16: Wipers and Washers 2007 Freestar/Monterey Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/27/2006
Wiper Motor — Windshield Printable View (104 KB) Removal

1. Remove the windshield wiper arms.

1. NOTE: Disconnect the washer hose before removing the cowl panel grille.
   Remove the pushpin-type retainers and the cowl panel grille.

1. Remove the washer hose grommet from the cowl panel and position aside the washer hose.

1. If equipped, remove the A/C air inlet filter.

1. Remove the 9 cowl panel bolts and position aside the cowl panel.

1. Disconnect the windshield wiper motor electrical connector.

1. Remove the cowl panel from the vehicle.

1. Remove the 4 bolts and the windshield wiper motor.

1. Position the wiper pivot arms on the windshield wiper motor and install the bolt.
   • Tighten to 15 Nm (11 lb-ft).

1. Install the 3 windshield wiper-to-cowl panel bolts.
   • Tighten to 15 Nm (11 lb-ft).

1. Position the cowl panel in the vehicle and connect the windshield wiper motor electrical connector.

1. Install the washer hose and grommet in the cowl panel.

1. Install the 9 cowl panel bolts.
   • Tighten to 6 Nm (53 lb-in).

1. If equipped, install the A/C air inlet filter.

1. Position the cowl panel grille in the vehicle and connect the washer hose.

1. Install the pushpins.

1. Install the windshield arms and nuts.
   • Tighten to 27 Nm (20 lb-ft).

1. Cycle and park the windshield wipers to check for correct alignment.

Owner Guide 1st Printing (.pdf). go to (owners guides and owners manuals/ford,lincoln and mercury owners). once pdf opens up then go to roadside emergencies,fuses and relays then scroll down to fuse diagrams. hope that helps.

Adjust the seat so it's folded and upright. Near where the seat is attached to the floor is a "square shaped" metal bar (attack from the bak of the seat). Pull that bar to release the floor clamp. Note I had to lean the chair to about 45 degrees to get it to work. It took a fair amount of pulling and cursing. Now that it's out, I'm going to spray the clamp with a little WD40. Maybe next time it'll work more smoothly.

Possible you have a faulty fuel injector. If no fuel is sprayed into the cylinder, it will show a misfire.

Yes, it is exactly TORQUE CONVERTER. Ford is re-calling over 400,000
Freestars accross North America for Torque Converter replacement. The new usnits became available in spring of 2012.
Splines on the original torque converter that make contact with input shaft of the transmission, weren't properly hardened and wear out pre-maturely. This causes transmission on act as if in neutral in every gear, except PARK due to lock engaging.
Free replacement at any Ford dealer. Put yourself on waiting list, if your trans totaly fails, then it will be looked right of way.

On the 4.2 engine, 1-2-3 are near the windshield.

if you have aux button there is a plug wire that mite be in the dash of the car, you could go to the radio manufacture website see if you can find the users manual, or installation guide, operational manual, the aux mite be a wifi option on other device of similar radio, that radio may have many versions and the version you got does not have that option with the cheaper version of radio that was installed when the car was made.
go to manufactures website, service, make, model,
it may need drivers to run the aux.

Here is a link to your owners manual, all fuse info in in there. Fuse info is starts on page 234 of pdf file http://www.fordservicecontent.com/Ford_Content/catalog/owner_guides/06winog3e.pdf