20 Most Recent 1987 Dodge Shadow Questions & Answers


SOUNDS LIKE YOUR VALVES ARE A LITTLE LOUD

1987 Dodge... | Answered on Sep 22, 2012


YOU WILL NEED TO REPLACE THE WINDOW REGULATOR ASWEMBLY TO FIX THIS PROBLEM..

1987 Dodge... | Answered on Aug 28, 2012


this sounds like you may have a bad tire, i would also have the alignment done and maybe balance all the tires if this has not been done in a while but the problem you list is more like a bad tire, good luck, hope this is helpful.

1987 Dodge... | Answered on Oct 26, 2010


The cost can very depending on what store.I would call every store and you should be able to purchase this particular one for about 25 to 45 dollars

1987 Dodge... | Answered on Oct 19, 2010


The power loss light goes on as a result of the alternator being bad.
Are you getting 'lifetime' guaranteed rebuilt alternators to replace the old ones?
If not, then the quality of the parts may not be good enough to run in your application.

Are the connections clean and shiny when removed?

1987 Dodge... | Answered on Oct 12, 2010


The specification calls for 900 rpms for the idle speed when warm for the 1987 Dodge Shadow.

One can adjust this with a screw on the carburetor, if it has one.

If it's fuel injected the idle speed is automatically controlled.

Fast Idle Speed HOLLEY 5220/6520 Fig. 5: Turn the adjusting screw with a screwdriver to raise or lower the fast idle speed — make sure that the adjusting screw is resting against the lowest speed step 86735g04.gif
NOTE: This procedure is performed while the carburetor is installed on the engine.
  1. On 1981–82 cars, disengage the two-way electrical connector at the carburetor (red and tan wires).
  2. On all years, disconnect the jumper wire at the radiator fan and install a jumper wire so that the fan runs continuously.
  3. On 1983–86 models, pull the PCV valve out of the valve cover and allow it to draw underhood air.
  4. Disengage the oxygen sensor system connector located on the left fender shield near the shock tower.
  5. Ground the carburetor switch with a jumper wire.
  6. Open the throttle slightly and place the adjustment screw on the slowest speed step of the fast idle cam.
  7. With the choke fully open, adjust the fast idle speed to comply with the value indicated on the underhood sticker.
  8. Return the vehicle to curb idle, then reposition the adjusting screw on the slowest speed step of the fast idle cam to verify fast idle speed. Re-adjust as necessary.
  9. Turn the engine OFF, remove the jumper wire and reconnect the fan.
  10. Reinstall the PCV valve and remove the tachometer. On 1983–86 models, reattach the oxygen sensor system connector, and remove the jumper wire from the carburetor.
Fast Idle Opening MIKUNI
  1. Before adjustment, leave the carburetor alone for approximately one hour at 73°F (23°C).
  2. Adjust the fast idle opening by turning the fast idle adjusting screw to the following specified values (drill diameter):
    • 2.6L engines equipped with manual transaxles — 0.028 in.
    • 2.6L engines equipped with automatic transaxles — 0.031 in.
Choke Valve Setting MIKUNI Fig. 6: After tightening the choke cover lockscrews, cut the heads off of lockscrews A (total of 3 screws) and stake the heads of lockscrews B (total of 2 screws) with a blunt punch 86735g56.gif
NOTE: This procedure need only be performed if the carburetor is disassembled.
  1. Fit the strangler spring to the choke lever.
  2. Assemble the choke valve, aligning the inscribed line or black painted line on the tooth of the choke pinion with the inscribed line on the cam lever.
  3. Temporarily tighten the new lockscrews.
  4. Set the choke valve by moving the pinion arm up or down, align a punched mark on the float chamber cover at the center of the three inscribed lines, and secure the pinion arm with the lockscrews.
  5. Install the choke cover and tighten the lockscrews.
  6. Cut off the heads off of lockscrews A.
  7. Stake the heads of lockscrews B using a blunt punch.
Vacuum Kick HOLLEY 5220/6520 NOTE: This procedure is performed while the carburetor is installed on the engine. If the vacuum kick is adjusted to open the choke too far, the engine may stall or idle very roughly just after cold start. If it is adjusted so that the choke does not open enough, there may be black smoke in the exhaust. NOTE: To perform this procedure, you will need a hand held vacuum pump capable of producing at least 15 in. Hg (50.6 kPa) of vacuum. The vacuum kick diaphragm may be damaged if you attempt to retract it manually. You will also need a drill or dowel which has a diameter equivalent to the specification for Vacuum Kick in the Carburetor Specifications Chart.
  1. Remove the air cleaner. Open the throttle, close the choke and hold it in the closed position, and then release the throttle to trap the fast idle cam in the choke-closed position.
  2. Disconnect the vacuum hose at the choke vacuum kick diaphragm. Connect a vacuum pump and apply 15 in. Hg (50.6 kPa) or more of vacuum.
  3. Gently move the choke blade toward the closed position just until play is eliminated from the vacuum kick linkage (so that the vacuum kick is determining choke blade position).
  4. Insert the drill or dowel into the gap between the upper edge of the choke blade and the air horn wall, toward the center of the gap. The dowel or drill should just fit into the gap. If necessary, rotate the Allen head screw in the center of the diaphragm housing to create the proper gap and then recheck with the measuring device.
  5. Restore all vacuum connections and reinstall the air cleaner.

1987 Dodge... | Answered on Aug 05, 2010


It sounds like the coil

1987 Dodge... | Answered on Apr 30, 2010


Fouled spark plug? Bad wire? Rotor / cap new? Check those things out, wear a thick rubber glove, take the wire off the non working plug, put a screwdriver next to the wire (while car is running) and see if a spark is made. If it is, your plug is bad. If no spark, replace wires. Still no spark? Change your rotor and cap. Still no spark? Ignition module. Following those steps will save you some green.

1987 Dodge... | Answered on Apr 01, 2009


This help? click on link below. When you get there and want bigger pictures, click on them.


http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528018dabb

1987 Dodge... | Answered on Jan 08, 2009


It should be located on the front of the transmission near the pan. It's a 3-prong switch.

Dodge Shadow... | Answered on Feb 17, 2018


Check for a bad wheel bearing or shaft. and not sure if you have band brakes or pads on rear but whatever it is check to make sure drum or rotor is not grooved up.

Dodge Shadow... | Answered on May 27, 2017


There is no headlight relay.

Dodge Shadow... | Answered on Mar 16, 2017


If the nut is staked, unstake it with a screwdriver and use a breaker bar, or a ratchet with a pipe on the end to increase your leverage.

Dodge Shadow... | Answered on Mar 16, 2017


Most water pumps have a weep hole that leaks when the pump seal is broken. Usually indicates the water pump needs replaced.

Dodge Shadow... | Answered on Mar 01, 2014


chiltons guide

Dodge Shadow... | Answered on Nov 13, 2013


it sounds like it needs a new thermostat, they run under $10.

Dodge Shadow... | Answered on Nov 04, 2013

Not finding what you are looking for?
Cars & Trucks Logo

Popular Tags

15 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1993 Dodge Shadow
1993 Dodge Shadow

150 Questions

1994 Dodge Shadow
1994 Dodge Shadow

107 Questions

1991 Dodge Shadow
1991 Dodge Shadow

51 Questions

1990 Dodge Shadow
1990 Dodge Shadow

44 Questions

1992 Dodge Shadow
1992 Dodge Shadow

-16 Questions

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Shadow Dodge

  • Shadow Dodge

Most Popular Question

pulls right

  • Cars & Trucks
Loading...