Serpentine belt routing diagram 2005 dodge 2500 4X4 cummins diesel
im assuming with a/c lol good luck
Posted on Jan 20, 2011
I am have an intermitten transmission problem with my 2005 Dodge Ram QuadCab 4x4, 5.9 Cummins (48RE Transmission).
Sometimes the transmission will not shift into 3rd or 4th gears. If I stop the vehicle, turn off the engine and sit for 30 seconds or so then restart, the vehicle will shift fine. As I said this is intermitten and sometime might not do it for 2-3 days then will flare up maybe once or twice during a days, then again not for a couple of days.
My wife is getting ready to take it to a shop and have the computer checked to see if there are any faults. I have searched the internet for possible problems and they have ranged from a bad input/output speed sensor, Govenor Pressure Sensor, Governor Pressure Solenoid.
We have changed the filter and fluids.
Any help would be appreciated!
Thank you
i had this problem with a friends 05 dodge 3500. i dropped the pan off the transmission, changed the governor pressure soleniod, trans filter and adjusted front and rear bands. also increased transmission pressure. this solved the problem he was having. you will need to have pressure gauges and a few special wrenches to do this yourself. also there is a valve in the transmission lines that has to be drilled out. this work not recommened unless you know what you are doing.
Posted on Feb 15, 2010
i have code p0973 on my 2005 Dodge diesel how do I fix the problem and what is the cause?
the problem is with the transmission overdrive circuit voltage is low. start by checking the #5 fuse in the fuse block under the hood. if it is ok check for voltages at the trans control relay. past that you may need to take it to a reputible technician for further diagnosis
Posted on Jan 11, 2009
what is the correct antifreeze for 2006 dodge 2500 ram diesel truck
Hi
Zerex's G-05 type coolant is specifically formulated for Chrysler specs.
See link
http://www.autoparts2020.com/rsdev/part_detail.jsp?PART_HDR_ID=60961
Thanks for using FixYa and please do rate my answer.
Posted on Nov 22, 2009
I have a 1995 Dodge Ram 2500, I am re-wiring my trailer harness; can you tell me what the black 12 gauge, lightblue 14 gauge, and the purple 16 gauge wires are for? I have accounted for all the others, I just dont know what these ones are for.
I have always had success when using these diagrams to wire trailer connections.
Posted on Jun 12, 2010
I need the injector circuit wiring diagram for a 2005 dodge ram with 5.9l cummins diesel .
What part of the circuit do you require?
go to www.dieseltruckresource.com
It's a really good forum for dodge diesel owners. Ask the question there and you should get all the help you need.
Posted on Jul 05, 2010
How do I change fuel filter in 2005 Ram 1500 4.7L? If it is located in tank are there any tricks to getting it out more easily?
My engine seems to surge from idle to around 1100 RPM down to 600 RPM when I come to stop, change from drive to reverse, and when I bring truck back to stop again. Then it smooths back out after couple seconds. am I barking up the wrong tree here with the fuel filter?
Thanks
Jerrod
Sounds like you may be experiencing one of a few possible issues. If you have an external fuel filter, you may consider in replacing this first. If the filter is part the fuel pump inside the fuel tank, may have to replace the entire unit. Might need to drop the tank from the vehicle if you do not have a was to access from the inside.
Do you have any codes in your ECM ?
Posted on Jun 24, 2017
wiring diagram for dodge 2005 pick-up tail lights,need to hook up 4 prong trailer light plug in
You are aware that you can buy an adapter that will plug in to harness under truck at back and will allow you to plug a 4 prong directly in to it. No cutting or splicing necessary that way. Any RV shop, as well as most auto parts stores now stock them.
Posted on Nov 12, 2011
radiator drain plug wont seal back up on my 05 dodge ram cummins
I have a 2004 Dodge Ram 2500 and to fix this problem I removed the drain plug being careful not to damage the plastic housing. I drilled through the center of the drain plug so that I would not have to use force to get it out and crack the plastic housing. After you get it out you will see that there is a rubber washer that is used to seal the drain. NAPA sells a drain plug that will work to replace the stock plug. The part #605-1278 comes on a card that says for Ford/GM. but it worked perfectly for me.
Posted on Aug 27, 2010
Diagnostic code P 340 and P 341 Camshaft Position Sensor Malfunction for a Dodge Ram Diesel 2500. What does it mean?
The Camshaft Position Sensor tells the PCM (computer) the position of the Camshaft Position. This Sensor sychronized along with several other Sensors including the Crankshaft Position Sensor the firing of the electronics to the spark plugs of each cylinder.
It is not difficult to replace and relatively inexpensive.
1. Disconnect the Negative side of the Battery,
2. Locate the Sensor and unplug.
3. Remove the Position Sensor retaining bolt.
4. Pull out the Sensor.
Replacement is reverse of above order.
Hint: use fresh engine oil on the end/sides of the Sensor especially around the rubber o-ring(s) to ease pushing the Sensor into proper position.
Posted on Nov 18, 2009
568 questions posted
Usually answered in minutes!
129 Questions
753 Questions
645 Questions
435 Questions
336 Questions