ok i got a 1995 ford ranger 2.3L got 140k mile in it...
and my check engine light come on... and the ranger got a obd 2 in it...so i use my obd2 reader...but my reader only read 1996 or up! so what should i do? is my ranger have obd2 or obd1?
since the reader dont have 95 ranger..so i choose the 96 ranger....its come out with a code" p1443" so how can i fix it? anyone know?
if your obd2 scanner fits the connection you have obd2, obd1 connector is way differnt.
your code p1443
Control System
Canister Purge
Valve (Mechanical)
Malfunction
Monitors the fuel vapor
flow between the
engine intake manifold
and the EVAP
canister. The system
failure occurs when a
leak or blockage
between the intake
manifold, the EVAP
canister purge valve
and the EVAP canister
is detected by the
PCM.
l Pinched, blocked or
plugged fuel vapor
tubes/hoses (except
between fuel tank and
EVAP canister)
l Damaged EVAP
canister
l Disconnected, cracked
or cut fuel vapor
tubes/hoses (except
between fuel tank and
EVAP canister)
l Damaged EVAP
canister purge valve
Check for audible vacuum
noise in the engine
compartment or significant
fuel odor in the engine
compartment or near the
EVAP canister.
This link has all the codes you need.
http://rockledge.home.comcast.net/~rockledge/RangerPictureGallery/DTCs.pdf
Posted on Dec 16, 2008
changed sparkplug wires and motor runs really rough.need diagram to put wires where they belong please.
I have a 95 Ford Ranger, 3.0,V6, need spark plug diagram, and firing orderto finish project!
thanx
1991-1994 2.9L and 3.0L Engines Firing Order 1-4-2-5-3-6
1995 And Later 3.0L V-6 With DIS Ignition System Firing Order 1-4-2-5-3-6
4.0L Engines Firing Order: 1-4-2-5-3-6 DIS Ignition System
Posted on Nov 23, 2008
checked all fuses and relays. there ok. changed the wiperblade motor out. when i plugged it in and tested it before i put it in, it worked. then after getting it all back together. it was dead. i took the motor back and got another just in case that motor was bad but still nothing. i would hate to change the switch out if is a ground problem. what do you think?
There is also a box inside the radio compartment area where the radio mounts that has the door open / key in ignition alarm. If someone unplugged this to disable the annoying ding ding ding; it will also disable the wipers. I wouldn't want to tell on myself but I guess I just did.
Posted on Jul 24, 2009
how to install a slave cylinder on a 95 ford ranger
The easiest way to deal with this problem is to order the complete preblead slave cylinder kit.
You can, just go with a new slave cylinder but because of the age of the other parts. You may run into other problems down the road. Why have to do it twice.
To replace the slave cylinder only:
Its easy, just carefully push/remove the small metal pin that hold the plastic line to the slave cylinder. then push-in and turn counterclockwise, to remove slave cylinder. Then install new slave cylinder and reverse the procedure. Now bleeding the system will take a while. But all you will do is just keep pumping the clutch pedal until the pedal returns.
Posted on May 19, 2010
fuse box diagram 1995 ford ranger horn stopped working does it have a fuse
On this website you find fuse box diagram and description for Ford Ranger (1995)
https://www.carknowledge.info/ford-ranger-1993-1997-fuse-box-diagram/
https://www.autogenius.info/ford-ranger-1993-1997-fuse-box-diagram/
Posted on Oct 08, 2019
wiring schematic for 1995 ford ranger starter relay
Is there a fusible link on the starter of a 1997 Ford Ranger, 2WD, 4.0 L
Posted on Dec 20, 2010
I need a fuse diagram for a 1995 ford ranger to find where the four wheel drive fuse is . thanks
It is fuse 13.
Please rate this solution.
Posted on Jan 10, 2011
i need wiring diagram for 1995 ford ranger XLT i need to hook up trailer lights
Unfortunately this model has separate filaments for the stop and turn signals. You will need to use an adapter relay to hookup a standard trailer plug or you will need a trailer that also uses this wiring setup. The first diagram below indicates there my be a trailer adapter for the turn signals at the base of the steering column. The wire colors at the bulbs are as follows:
tail/running lights: brown
stop: light green
left turn: light green/white stripe
right turn: white/light blue stripe
back up: black/pink stripe
ground: black
Please let me know if you have questions.
Posted on Oct 08, 2011
i have a 95 ford courier ute , which wont start ,i thought i may have run it out of fuel but put petrol in and took one of the hoses of to make sure the fuel was going through the lines ,tryed clutch starting it ,turns over just wont spark
check crank position sensor
Posted on Oct 11, 2012
Wiper motor quit working. changed relays, fuse is ok, and got a new motor. What else can I check?
Do you have int wipers? If so check the int module its under the dash right side of the steering column I believe. Specifically check the solder joints.
Posted on Jun 16, 2014
534 questions posted
Usually answered in minutes!
642 Questions
645 Questions
573 Questions
562 Questions
558 Questions