20 Most Recent
2004 Ford Taurus - Page 2 Questions & Answers
What should the fuel pressure be for a 2000 ford
fuel pressure at the fuel rail test port should be at least 44 PSI, when u gun the engine it shuld go up very quickly, it should never drop, if it does the fuel filter is either plugged or the pump is defectuive
Need to find out which is cylinder number three
Hello jdakota1313: My name is Roger and I will help you. The fire order is 1-4-2-5-3-6. You will find #3 plug on the firewall side of the engine. rear plug just in front of the transmission bell housing. See the attached picture. Should you need further help please just ask. Please rate the answer you received. hank You for using Fix Ya. Roger
3.0 ford engine. what is the firing order
The rear three plugs, left to right are 1,2,3
The front three plugs, left to right are 4,5,6
The coil pack looks like this
--4 pin--
-----------------
--1--- 2--- 3--
----------------
--5--- 6--- 4--
-----------------
The firing order is 1,4,2,5,3,6
2004 ford taurus is running horrible
If you didn't change one spark plug wire at a time then you may have your firing order off...
Please pick your motor...front or rear wheel drive...
3.0L (VIN U) engine Firing order: 1–4–2–5–3–6 Distributorless ignition system
3.0L (VIN S) engine Firing order: 1–4–2–5–3–6 Distributorless ignition system
How to install replacement window on passenger side
you take off the door panel by using a panel clip tool to pop the clips for the panel to come off also check for any screws holding the panel to the door by the inside door handle the bottoms of the panel once you get it off unplug the window door switches to move the panel out of the way but first lower the window track so you can see it remove the weather seal plastic and then when you can get to the track and the glass you'll see that there should be yellow circle clips that pop together to hold the glass with rivets I'm assuming the glass is broken and this might have come off and is in the bottom of the door use these for the new glass after drilling out the old rivets snap them together one on each side of the new glass and then put bolts and nuts on to tighten or use a rivet gun to the track reconnect the switches for door window power and raise the glass
I have a 2004 taurus with the duratech motor. the
If the starter is spinning but it is not engaging the ring gear, you have a bad solenoid. This is to push the gear forward to turn over the engine. If the solenoid built into the starter or a separate part?
Anyway...it isn't connecting.
Semper Fi,
Z
Where is the starter located on a 2004 ford taurus
One of your positive battery cables goes to the starter motor. Dis connect negative battery cable. Safely raise and support the vehicle. You'll have to remove front splash guard from underneath. Ant time your working under a vehicle there are safety issues, safety is your responsibility.
2004 ford taurus keyless programming mode activate problems
first check for blown fuses and confirm that all are good next what are you trying to program? and this sequence has to be done quickly and the ignition left in the run position if its a key fob you must touch a button on it don't forget that if the sequence is not done properly the system has to time out before you try again if its a chip key theres a battery in some of them
Code P1405
I have copied the entire description for the code.Let me know if you need more info. You may need a shop to take a look at the system.P1405 Ford Description
The purpose of the Exhaust Gas Recirculation (EGR) system on your
engine is to limit oxides of nitrogen (NOx) emissions. This is done by
redirecting small amounts of exhaust gas back through the upper intake
to get mixed in with the air/fuel charge. The resultant diluted air/fuel
mixture (i.e., less oxygen per cubic foot) burns cooler and combustion
chamber temperatures are reduced accordingly, thereby lowering NOx
emissions. The Ford DPFE/EGR system is controlled by the
Powertrain Control Module (PCM). The system employs an EGR Valve, an
Electronic Vacuum Regulator (EVR), and a Delta Pressure Feedback EGR
sensor (DPFE). The DPFE Sensor measures EGR flow across an
orifice located inside the special EGR Tube. The orifice is positioned
between two hose ports coming off the tube which are connected to the
DPFE sensor with special heat-resistant hoses. When the EGR Valve is
open, a pressure differential is created across the orifice (intake
manifold pressure vs. exhaust pressure). By design, this difference in
pressure is measured by the DPFE sensor in terms of voltage. The DPFE
voltage signal output to the PCM is directly proportional to the flow of
exhaust gas entering the intake manifold. Read more:
http://engine-codes.com/p1405_ford.html#ixzz2dUIwIiDd
Not finding what you are looking for?