Top 10 2001 Dodge Neon Questions & Answers

2001 Dodge Neon Logo

Question

  • 3,659 People Helped

how to install alternator belt 2001 Dodge

how to install alternator belt 2001 Dodge
neon

Posted by on

Answer

  • Most Helpful of 1 Answers

Below is a diagram for the belts on your car. You will see to the right, an adjusting bolt. This loosens the tension to slide the belts on and off. Once the new belt is on, apply pressure to get the belt tight (a long flathead screwdriver or crowbar should do) and while tight, re-tighten the adjusting bolt.
da5dc36.jpg

Posted on Oct 18, 2009

Question

  • 2,846 People Helped

Car will not heat up

The car will not heat up at all. No matter how long the car is running it still wont get warm. I thought that it might be the thermostat. but then i checked the radiator. I checked the radiator fluid, and there was no pressure. the fluid wasnt flowing through the tubes at all, and it would heat up a little bit if i squeezed the tubes and then it heated up a little bit. but then went cold again. What could be wrong.

Posted by on

Answer

  • Most Helpful of 2 Answers

Did you "bleed " the system when you filled it with coolant ? You have to put in a some coolant and water.1/2and 1/2 mixture, Make sure it is the right coolant. All color coolant works fine.Rune the vehicle for a while . Turn off the vehicle and let it cool. Turn the radiator cap and a hiss of air will come out. Use a Rag . Be careful not to burn yourself. The pour some more coolant and water . And repeat the process until radiator is full. Some cars have a bleeder valve that you turn counter clockwise with a screwdriver near the thermostat housing or near the radiator hose .

Posted on Jan 09, 2009

Question

  • 2,407 People Helped

i need to change the starter in my 2001 dodge neon

i need to change the starter in my 2001 dodge neon

Posted by on

Answer

  • Most Helpful of 1 Answers

The starter is located under the car where the transmission and engine meet toward the front of the neon. The starter actually bolts up with face toward the transmission. You must get the car up on ramps or on a hoist to see the starter. This is just a general method; it is very hard to give words to describe some of the steps without pictures. Removal: Disconnect and isolate the battery negative cable. Raise vehicle on hoist. Remove starter bolts. Remove starter assembly. Disengage latch and remove solenoid connector from starter assembly. Remove battery positive connector from starter assembly. It is not necessary to remove the alternator output lead from the connector. Installation: Clean corrosion/dirt from the cable and wire terminals before installing wiring to the solenoid. Attach battery positive connector to starter. Ensure alternator output connector is snapped into the battery positive connector. Tighten the captive nut to 10 Nm (90 in. lbs.) . CAUTION: It is critical that the alternator output terminal be connected to the battery positive terminal of the starter solenoid, for proper operation of the charging and cranking systems. Install solenoid connector to starter. Ensure that latch is fully engaged. Position the starter face into transmission housing. Start bottom mounting bolt and thread in until bolt is snug. Attach ground cable to upper starter mounting bolt. Ensure the proper starter alignment before tightening the starter mounting bolts to 54 Nm (40 ft. lbs.) torque. Lower vehicle and connect negative battery cable.

Posted on Jul 13, 2010

Question

  • 2,374 People Helped

como saco el motor de arranque

como saco el motor de arranque

Posted by on

Answer

  • Most Helpful of 2 Answers

Espero que la taduccion sea clara...

Remoci?n e instalaci?n - Motor 2.0L

1. Antes de reparar el veh?culo, consulte la secci?n de Precauciones.
2. Retire o desconecte la siguiente:
Cable negativo de la bater?a
La manguera de entrada del colector de admisi?n y vuelva a colocar la caja del filtro de aire, en los motores de alto rendimiento s?lo
Arranque el?ctrico conectores
Gu?a de iniciaci?n a los pernos del motor
Arranque

zjlimited_845.jpg
Fig. Arranque de montaje-2002 muestra de ne?n, otros similares
Arranque de montaje-2002 muestra de ne?n, otros similares

Para instalar:

1. Instalar o conectar los siguientes:
De arranque y el par pernos a 40 lbs. (54 Nm)
Arranque el?ctrico conectores
La ingesta de la manguera de entrada m?ltiple en los motores de alto rendimiento
Cable negativo de la bater?a


Solenoide o rel?

El rel? se encuentra en el Centro de Distribuci?n de Energ?a (PDC) en el compartimiento del motor. Consulte la parte inferior de la cubierta del PDC para la localizaci?n de rel? de arranque. Simplemente desconecte el rel? para reemplazarlo.

Aqui la traduccion original (en ingles).

Suerte.

Removal & Installation - 2.0L Engine

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Inlet hose from the intake manifold and reposition the air cleaner box, on high output engines only Starter electrical connectors Starter-to-engine bolts Starter

    zjlimited_844.jpg

    Fig. Starter mounting-2002 Neon shown, others similar
    Starter mounting-2002 Neon shown, others similar

To install:
  1. Install or connect the following:
    Starter and torque bolts to 40 ft. lbs. (54 Nm) Starter electrical connectors Intake manifold inlet hose on high output engines Negative battery cable
Solenoid or Relay
The relay is located in the Power Distribution Center (PDC) in the engine compartment. Refer to the underside of the PDC cover for starter relay location. Simply unplug the relay to replace it.



Hope this helps.

Posted on Mar 11, 2011

Question

  • 2,013 People Helped

Rough low idle in gear when stopped at a light.

2001 Neon engine idles rough in gear when stopped at a light. Idle seems to drop real low but I can't tell you how low as there is no tach. Does not exhibit problem when in neutral/park. Otherwise car runs great at all speeds.

Posted by on

Answer

  • Most Helpful of 1 Answers

probable vacuum leak query brake booster

Posted on Jul 26, 2009

Question

  • 1,881 People Helped

no spark from 2001 dodge neon se 2.0 i've replaced cam shaft sensor, crank sensor,coil still no spark

my neon isn't getting spark i have replaced the camshaft sensor,crank sensor,coil i'm thinking it could be the knock sensor not sure i thought it was the pcm but not sure of that either

Posted by on

Answer

  • Most Helpful of 2 Answers

For no spark problem,click the link below :---Car has no spark? http://schematicsdiagram.blogspot.com/2011/06/car-has-no-spark.html

Posted on Feb 13, 2012

Question

  • 1,858 People Helped

Code P0442

Code P0442 Engine Light

Posted by on

Answer

  • Most Helpful of 1 Answers

Causes A code P0442 most likely means one or more of the following has happened:

  • A loose or improperly affixed gas cap
  • A non-conforming gas cap (i.e. not factory/original brand)
  • A small leak/hole in a fuel vapor hose/tube
  • Other small leak in EVAP system
  • Faulty vent o-ring seal
Possible Solutions With a P0442, the most common repair is to:
  • Remove and reinstall the gas cap, clear the codes, and drive for a day and see if the codes come back.
  • Otherwise, replace the gas cap, or
  • Inspect the EVAP system for cuts/holes in tubes/hoses

Posted on Aug 04, 2009

Question

  • 1,797 People Helped

What kind of coolant does

What kind of coolant does my 2001 Dodge neon ES need?

Posted by on

Answer

  • Most Helpful of 2 Answers

chrylser recommends their antifreeze, and it is called hoat, you can purchase this at the chrysler dealerships at their parts dept.

Posted on Apr 09, 2011

Question

  • 1,674 People Helped

2001 Dodge Neon won't start. says "fuse"

the odometer flashing "fuse" when I try to start my 2001 dodge neon. The engine turns over, but no ignition.

Posted by on

Answer

  • Most Helpful of 1 Answers

check all you r fuses. There should be 2 sets, one under the hood and another in the passenger area(driver side under dash usually)

Posted on Jul 18, 2009

Question

  • 1,543 People Helped

check engine light blinking 10 times

the check engine light stays on the time that engine is running.When I turn the switch to the on position before starting the car the instrument panel dings six times after which the check engine light blinks ten times then stays lit.I have a dodge Neon 2001

Posted by on

Answer

  • Most Helpful of 1 Answers

The pcm (powertrain control module ) is telling you it has a set code in the memory. Take the car to a parts place like (auto zone ) and have them to run a scam on the pcm for a trouble code. Once you have done that then you will be able to correct the problem. Hope this will help you.

Posted on May 27, 2010

792 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2002 Dodge Neon
2002 Dodge Neon

839 Questions

2004 Dodge Neon
2004 Dodge Neon

733 Questions

2003 Dodge Neon
2003 Dodge Neon

727 Questions

2005 Dodge Neon
2005 Dodge Neon

688 Questions

2000 Dodge Neon
2000 Dodge Neon

598 Questions

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

2001 Dodge Neon Neon

  • 2001 Dodge Neon Neon

Most Popular Question

car goes off before release clutch

  • Cars & Trucks
Loading...