20 Most Recent 2005 Chrysler 300 Questions & Answers

You need to replace your cable it's either broken or disconnected

elloThe engine and transmission in this cars drive train are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant teperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL THE DIAGNOSIS & TESTING IS COMPLETED.

Go to the Prindle switch where the cable meets the transmission and check if it has not unhooked. Move the shifter all the way to the Park position and adjust/tighten.

on the earlier chryslers that was the plenum tuning valve

Check out the videos https://www.google.com/search?q=2005+Chrysler+300+AWD%2C+Replace++speed+sensors and location images https://www.google.com/search?q=2006+chrysler+300+transmission+speed+sensor+location&rlz=1C1QJDB_enCA643CA644&sxsrf=AOaemvIMDTfQ6-78ZXo9WExIjLbuRiyuBA:1642731779633&source=lnms&tbm=isch&sa=X&ved=2ahUKEwiNnb7h5MH1AhUBjYkEHcgmA_cQ_AUoAnoECAEQBA&biw=1920&bih=937&dpr=1 ..

Instructions

1. • 1 Ensure that the doors, hood, decklid and rear liftgate are properly closed. The alarm cannot properly arm if any of the doors or other openings are not closed.
   • 2 Replace the batteries in the key fob to ensure that the remote is capable of arming the alarm system. If the batteries have been dead for more than a few minutes, the fob will need to be synchronized with the vehicle to function. To synchronize the remote with the car, aim the remote at the vehicle and press the lock or unlock button twice. Next, place the key in the vehicle's ignition and turn the ignition switch to the "On" position. All of the steps must be completed within 30 seconds.
   • 3 Verify that the parking lamps flash three times when the system is armed using the remote. Alternatively, verify that the alarm is armed by looking at the alarm indicator on the dash. If the alarm is properly armed, the alarm indicator light should blink.

Dealer or mechanics know how to get it open and replace the release cable.

I have a leak on the side of my radiator can u tell me what I should do

RKE means remote keyless entry. Install a new battery in your key fob and your light will go off. Regards, Joe
ps - kindly rate my answer as helpful. thank you.

Assuming you used the correct replacements, probably a wiring problem in the column or a connector problem. Carefully check the connections at the bottom of the column.

You need to change the bulb there.

Hello! See diagram below of the location of Crankshaft Positioning Sensor (CPS)...It has a 3 wire connector with the following wire colors...Dark Blue/Dark Green (ground)...Dark Blue/White (signal lead)...And Pink/Yellow (+5 volts)...Looking at the front of the engine...The left bank (front to rear) are 2, 4, 6, 8...The right bank (front to rear) are 1, 3, 5, 7...Therefore the first cylinder on the right bank is # 1...The rear or last cylinder on the right bank is #7Guru...............Saailer I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

Should be fuse #4 a 20amp (yellow in color) located in the IPM (integrated power module) on passenger side engine compartment. Black cover over IPM.

didn't bother and refill the radiator nothing gets fixed until you take the timer to have it fixed

burning oil ? leaks on the ground still ?

Very hard to diagnose nav /stereo units. Check fuse box to make sure it's getting a good power supply. Try spraying WD-40 or contact lens cleaner in the switches to see if any of them are stuck. Consider replacing entire unit w/ one from eBay, preferably with some kind of warranty. Also, check Crutchfield.com for new alternatives. A factory replacement, if you can find one, is likely to be really expensive.

It look like your ECU does not recognize the throttle body. Reasons being removal of battery for a long time. Try doing an adaption and also run a Diagnostics for other issues

Check the codes.