Top 20 2006 Chrysler 300 Questions & Answers


You can try out some guide from here reliable-store they also provide live chat feature for instant help and it's very useful

2006 Chrysler... | 33 views | 0 helpful votes


Definitely possible that your vehicle was secured incorrectly for towing.

2006 Chrysler... | 35 views | 0 helpful votes


If thermostat is ok then you could have an air lock in your radiator.
Possible water pump not working properly such as the impellor slipping..
Radiator may be partly plugged and not letting the fluid flow.
Are your belts tight enough so they do not slip. Your main belt lightener may not be working so when the engine speeds up it slips instead of working.

2006 Chrysler... | 312 views | 0 helpful votes


Hello 2006 Chrysler,

If your talking about the component that is located along the air duct run from the air filter to the throttle body it is caled a MAF sensor.
Mass Air Flow Sensors Components

2006 Chrysler... | 544 views | 0 helpful votes


if the shifter is on the column remove plastic cover there is a small metal bar that moves it needs some grease or wd 40 on it

2006 Chrysler... | 27 views | 0 helpful votes


5.7L Engines

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Drain the cooling system.
  4. Disconnect negative battery cable.
  5. Remove the upper radiator hose.
  6. Disconnect cooling fan electrical connector.
  7. Remove cooling fan mounting bolts.
  8. Remove the radiator cooling fan assembly from vehicle.
  9. Remove the radiator fan assembly.
  10. Remove accessory drive belt.
  11. Remove thermostat.
    NOTE The water pump mounting bolts are different lengths. Note the location of the water pump mounting bolts.
0996b43f80200d65-mw3da2o1okphbx00ygfzxzdl-4-0.jpg To install:
  1. Install water pump and mounting bolts. Tighten mounting bolts to 20 ft. lbs. (28 Nm).
  2. Make sure double ended bolt is in the proper location. Tighten double ended bolt to 20 ft. lbs. (28 Nm).
  3. Position the radiator cooling fan assembly in vehicle.
  4. Install cooling fan mounting bolts. Tighten to 50 inch lbs. (6 Nm)
  5. Connect the cooling fan electrical connector.
  6. Install the upper radiator hose.
  7. Install thermostat.
  8. Install the accessory drive belt.
  9. Install the radiator fan assembly.
  10. Connect negative battery cable.
  11. Fill the cooling system.
  12. Pressure test cooling system.

2006 Chrysler... | 137 views | 0 helpful votes


Test the sender first. It could just be a poor electrical connection on the sender or the sender itself. Check oil level too. If you have a lot of miles on the engine it's possible the oil pump is worn.

2006 Chrysler... | 164 views | 0 helpful votes


The power distribution center contains 5A fuse 35 and circuit breaker 3.

2006 Chrysler... | 954 views | 0 helpful votes


If your battery is dead your alternator is probably not working

2006 Chrysler... | 59 views | 0 helpful votes


go 2 the store and get one i am a MECHANIC and no they are good

DIng

2006 Chrysler... | 267 views | 0 helpful votes


The dipstick tube is at the rear of intake, has a black plug but no dipstick. Just about center of intake, near fire wall.

2006 Chrysler... | 57 views | 0 helpful votes


The fuel pump normally only comes on for a second unless the car starts and is running, if the car starts and the pump only runs for a few seconds, then there is a problem with the engine signal to the ecm, ie its not telling the computer that it is running. I dont believe there is a schrader valve on those fuel lines, if there is, chrysler probably put it underneath the intake plenum. If the car will not start, but you hear the fuel pump kick on and off, it could have a clogged fuel filter, or injectors, or even bad connections going to the injectors. They normally are all switched via the ground wire for each injector, so if they are not cycling it could be a bad ecm, or bad connection somewhere in the wiring harness

2006 Chrysler... | 92 views | 1 helpful votes


I think there is a dealer letter about this and a factory fix, check with the local dealer.

2006 Chrysler... | 55 views | 0 helpful votes


Mobile lock smith that can check diagnostic trouble codes ! If the light is on their are codes stored . It may not have anything to do with a key or two keys . Your assuming .Have it check for DTC'S

2006 Chrysler... | 36 views | 0 helpful votes


I would try the upgrade again and if that fails contact the dealer to see if there is a problem with the disk or a bulletin about the issue for your year and model.

2006 Chrysler... | 49 views | 0 helpful votes


You need to scroll through the functions on the instrument panel display until you find the the sound horn when locking function and activate it. Iff you are unsure how to access the instrument panel functions, the owners manual will guide you though the process

2006 Chrysler... | 103 views | 1 helpful votes

Not finding what you are looking for?
2006 Chrysler 300 Logo

1,037 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

300 Chrysler

  • 300 Chrysler

Most Popular Question

chrysler 300 06 old pump new pump

  • Cars & Trucks
Loading...