20 Most Recent
1992 Isuzu Rodeo - Page 8 Questions & Answers
My front wheels for my
If you live near a Les Schwab then take it to them,the inspection is free, it sounds like you have ball joint that is coming apart or a tire that has separated,if you want to do it yourself then make sure the car is in park and chock the rear tires so it can't move then jack up the front end you can do one side at a time or both it's up to you just make sure to support the car on jack stands,once it is up off of the ground put one hand on the top of the tire and one on the bottom then try to make it move by pushing in at the top and pulling out at the bottom it shouldn't move then do the same thing on the side of the tire this will let you see if your tie rod ends are ok they shouldn't wiggle in there socket.Also check your tires for bulges or sharp steel belts sticking through the tread face.Hope this helps and good luck
I want to know what
code 42
electronic spark timing circuit fault (c)
fuel cut -off relay malfunction or circuit fault (A)
it could be either one depend on engine size and all so vin#.
Need wiring diagram for 1992
For the 1992 Isuzu Rodeo 3.1L V6:
Firing Order:
1-2-3-4-5-6
Cylinders:
.....(back)
5...............6
3...............4
1...............2
Distributor:
.....(back)
..............(+)-screw
.........4
..3
...................5
2
.................6
........1
(+)-screw
.....(front)
Rotation: Clockwise
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!
Will not start after swapping
AAaahhh, the infamous Rodeo. Whenever I replaced the radio on the thing, it too would not start on me. I hope you have figured out the problem before you even read this. You have a blown fuse. It is a fuse that might say something ridiculous like RADIO or CIG. LIGHTER, but it is somehow linked to your ignition system. as you probably already know, the fuse boxes are under the driver's dash and in the hood, I don't exactly recall where. I would start by checking ALL of them. Good luck.
I’m happy to assist further over the phone at
https://www.6ya.com/expert/pedro_4520403b21ed459a
1999 flasher unit location?
On the fuse box(relay 4) situated in the left footwell of LHD vehicles or right side of the dash on RHD vehicles.
Can you use wd40 to loosen up a spark plug
hi well you could do but it really wont do you any good, as the plug has a seal on the end and as it is, it seals it, unfortunately the only way is brute force and ignorance so to speak, you can however try putting an extension in the hole with a smaller size socket on it and giving it a few good taps, this might loosen the plug enough to be able to turn it, but as i said its a case of putting some force into it, if you are changing them it shouldn't matter if it brakes the enamel covering in fact it might help ...hope this helps you out.
1992 Rodeo: My 1992 Izuzu Rodeo is having radiator trouble. Th...
It has to be the sending unit on the engine, you have to find it and replace it, if it is not overheating and not using coolant. I can't tell you where it is because I don't know what engine you have, but it should be up top, near the thermostat housing, you can unplug a couple things to find out which it is. It looks like a bolt with a plastic cap and wires coming out of it. Check it out.
Distributor wiring
For the 1992 Isuzu Rodeo
I do not know if you have the 2.6L SOHC In-Line 4-Cylinder or the 3.1L V6; however I have included both below.
For the 2.6L:
Firing Order:
1-3-4-2
Cylinders:
(back)
...4
...3
...2
...1
(front)
Ignition Coils:
(back)
1....2
3....4
(front)
For the 3.1L:
Firing Order:
1-2-3-4-5-6
Cylinders:
.....(back)
5...............6
3...............4
1...............2
Distributor:
.....(back)
..............(+)-screw
.........4
..3
...................5
2
.................6
........1
(+)-screw
.....(front)
Rotation: Clockwise
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!
I need a diagram of the timing marks on my Isuzu
I have just changed 3 Coils and 6 leads on my Isuzu bighorn 1992. The starter is turning when I keyed it, but there doesn't seem to be any electricity going through. Can you tell me what is the problem here?
New clutch still slipping
Lets start with what was replaced : Clutch pressure plate, throwout bearing,pilot bearing,input shaft bearing, was flywheel cut or replaced,Clutch cable or slave cylinder (whatever is applicable,) Lets see what repair shop says. Depending on what they say they did or didn't do we will take it from there.
keep me posted
Not finding what you are looking for?