20 Most Recent 1993 Isuzu Trooper - Page 8 Questions & Answers

replace bulb

Use a few squirts of starter fluid directed into the air intake. Remove the air cleaner if you wish in order to get a straight shot into the air intake. If it still will not start, you may want to have your battery checked, along with your charging system. Joe

turbocharger repairs are best left to a specialist as is is a complicated job which needs special tools

check engine light can only be turned of by a specialist with a computer

check the fuel filter it could be blocked

open the bonnet and look for a large round container with a alloy piece coming from the centre with a see through plastic container on top there will be a few copper or steel pipes coming from the alloy part under see through container unscrew black cap from see through container and put in brake fluid

G'day mate yes there is an easy way, take it to the mechanic and get it done , not being silly to just real, as the axle nut is held on with great torque it will be hard undo then you get to the partial dismantling of the suspension . Great Danger for the inexperienced here as springs hold an enormous amount of energy just waiting get out , really there's a lot to be caught out by when doing this job. as for the keys well a set may be taped to a wiring harness or behind the bumper which is where most people hide spares. hope this helps

My sincere apologies for the severely delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, however I am answering it in case you still do.

Click on the following direct Link. It has the Timing Belt Diagrams with Marks for the Camshaft and Crankshaft that you will need.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1993/make/isuzu/model/trooper/1993_isuzu_trooper_timing_belt_diagram_marks.htm

If your battery warning light is on, then your alternator is NOT working okay. Rather, maybe the alternator DOES work, but the battery light can also come on if your battery won't charge.

Put a voltmeter to the battery terminals when the engine is running and rev the engine to a medium idle. Battery charging, (engine running) it should be about 13.5-14.5 volts. Engine off fully charged battery voltage should be 12.6 volts.

Quick test-engine running, disconnect the positive battery terminal from the battery- if the engine dies, there is still an alternator problem.

Hope this helps.

Faulty cold start system

You need to change the head light bulbs, they have two elements one for normal lighting and one for high beams, the low beam elements on those light bulbs are burnt, install new ones and you'll fine. Good Luck

On some vehicles, the transmission has to be in neutral to shift into 4 low.

Are you towing with the o/drive on or off. Should be off, or the trans. will heat up too much. Then you will have damage.

Sounds like faulty earth. Re earth the tail light's clean paint off a small section of the bodywork strip about half inch of the black wire (earth) attach a piece of wire to it and connect it to the pannel with self tapping screw. Do not cut the black wire just strip it and connect to it.

If you are talking about the steering column cover, make sure that ALL of the screws are removed. you may have to remove the knee bolster (below the column) to make sure. Then just pry apart with fingers. they are clipped together in about 4-6 places around the seams to each other they can be a bear sometimes. What have you tried so far?

See my photo showing the diagnostic connector on the 1993 Isuzu.

I posted the answer on FixYa but the language I used calls the connector an OBD (on board diagnostics) connector.

http://www.fixya.com/PostComment.aspx?thid=1584937&prdid=0&ctgid=231

Hello veloruss: My name is Roger and I will try to answer your question so you can locate the terminal. You will find the ALDL connector on the right side of the drivers dash in the area of the gas pedal. Locate the white 3 wire connector. you will also see a green 3 wire connector with a single wire connector. Make sure you use the white 3 wire connector.Jump wires 1 and 3 together to obtain the computer codes. Should you need further help please just ask. Please rate the quality of the answer. This way I know the answer was correct. Thank You for using Fix Ya. Roger

you have abad dimmer switch on your sterring colum