Top 10 1995 Isuzu Rodeo Questions & Answers

with lights off and battery disconnected remove the twist knob on the dash that brighten and dims your dash lights and jump the two prongs with a jumper wire. connect battery and turn lights on all your dash lights should work now. if thay don't take the dash screws out and replace the bulbs, it's really easy if you have mechanical skills if not consult a friend that does. now you know the dash light dimmer switch is bad and they are hard to find i found mine in a wreck but until i did i just left the jumper wire in place (about a year and 1/2)

if you take off interior panel.....push out the dent with a bar....then try button if no work go back inside and you should see bars going down from handle to latch area...pull up on it and should pop the trunk

flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

123456 IS THE FIRING ORDER... RIGHT BANK (RIGHT AS IN SITTING IN THE DRIVERS SEAT NOT STANDING IN FRONT OF THE CAR)STARTING AT FRONT IS CYLINDER 1 THEN 3 THEN 5 THEN THE LEFT BANK IS CYLINDER 2,4,6, FRONT TO REAR... THE COILS FROM LEFT TO RIGHT (STANDING IN FRONT OF CAR) ARE 1,4,6,3,2,5 HOPE THIS HELPS

Great to hear the update, and that the car is up and running. Good luck with it,
Curt

Here is how I fold down the back seat of my 1995 Rodeo. First thing I do is remove the headrests on the back seat. Then I place my knees (and all my weight) on the middle of the seat (bench), and pull on both belts straps. If this is done properly, I will hear each strap release. (sort of a click). As soon as I hear it release, I stand up as best I can while at the same time pulling up the seat. I then manage to step out of the Rodeo while letting the seat fall forward. After that, I am able to drop the other part of the seat into the forward position.

Your 95 isuzu rodeo with the 3.2 liter motor holds five quarts in the crankcase, plus your oil filter capacity, which is half of a quart.If you are changing your oil and filter, add a total of 5.5 quarts of new oil.Hope I could help!!!! Thanks!!

To install:

1. Install new camshaft seals and retaining plates onto the cylinder. Tighten the right camshaft seal retaining plate 6mm bolts to 65 inch lbs. Tighten the left camshaft seal retaining plate 8mm bolts to 191 inch lbs.
2. Thoroughly clean the cylinder head and engine block sealing surfaces.
3. Place a new head gasket on the engine block and carefully position the cylinder head on top of the new gasket.

1. Install new cylinder head bolts and torque them in sequence to 47 ft. lbs. (64 Nm) for the M11 bolts and 15 ft. lbs. (21 Nm) for the M8 bolts.
2. Install the dipstick tube bracket to the cylinder head.
3. Connect the front exhaust pipes to the exhaust manifolds. Tighten the exhaust bolts to 48 ft. lbs. (67 Nm).
4. Install the power steering pump bracket. Torque the mounting bolts to 34 ft. lbs. (46 Nm).
5. Install the cylinder head covers.
6. Install the timing belt and the auto tensioner (pusher). Torque the mounting bolt to 14 ft. lbs. (19 Nm).
7. Install the timing belt cover and oil cooler hoses and bracket.
8. Install the crankshaft pulley. Torque the center bolt to 123 ft. lbs. (167 Nm).
9. Install the fan pulley assembly.
10. Install the power steering pump.
11. Install the accessory drive belts.
12. Install the engine coolant manifold and the heater hose.
13. Install the intake manifold. Torque the nuts and bolts to 17 ft. lbs. (24 Nm) in a crisscross pattern.
14. Install the fuel injector connectors and the fuel hoses to the fuel rail.
15. Install the common chamber. Torque the nuts and bolts to 17 ft. lbs. (24 Nm).
16. Install the EGR valve assembly. Torque the mounting bolts on the valve side to 69 inch lbs. (8 Nm) and the bolts on the exhaust side to 21 ft. lbs. (28 Nm).
17. Connect the evaporative emission canister purge hose.
18. Connect the fuel pressure control valve vacuum hose.
19. Connect the positive crankcase ventilation hose.
20. Install the throttle body assembly. Torque the mounting bolts to 14 ft. lbs. (19 Nm).
21. Connect the vacuum hoses to the throttle body.
22. Install the ignition control module and the spark plug wires.
23. Connect the MAP sensor; Canister vacuum switching valve (VSV); Exhaust gas recirculation (VSV); Intake air temperature sensor and ground connectors.
24. Connect the vacuum booster hose.
25. Connect the air vacuum hose.
26. Connect the accelerator cable. Adjust the accelerator cable by pulling the cable housing while closing the throttle valve and tightening the adjusting nut and screw cap by hand temporarily. Now loosen the adjusting nut by three turns and then tightening the screw cap. Make sure the throttle valve reaches the screw stop when the throttle is closed.
27. Install the cooling fan assembly and the upper fan shroud.
28. Install the air cleaner assembly.
29. Connect the negative battery cable.
30. Refill and bleed the cooling system.
31. Refill and bleed the power steering pump if necessary.
32. Refill the engine with fresh oil.
33. Run the engine and check for leaks and proper compression.

Amigo resolviste la falla ? A mi me pasa lo mismo en una dmax puedes escribirme a ver q hiciste porfavor. +584142106960

Hello Harvey, My information shows firing order of 123456. #1 being passenger's front cylinder and #2 being driver's front cylinder.